Seepex BN 100-6LS Скачать руководство пользователя страница 40

Страница: 40 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

12 (18)

Dismantling/reassembly

9.1.3.7 Rotor (600), coupling rod (400), plug-in shaft (307) - Dismantling

9.1.3.8 Lantern (200)/drive (ANT) - Dismantling

9.1.4 Pump - reassembly (SCT)

9.1.4.1 Base plate (GPU), lantern (200), drive unit (ANT) – reassembly

9.1.4.2 Rotor (600), coupling rod (400), plug-in shaft (307) - Reassembly



Joint (G) dismantling note rotating unit - in-
dividual parts (chapter 9.2).



Disconnect the drive (ANT) from the lan-
tern (200).



Remove the lantern (200) from the base
plate (GPU).

WARNING

Risk of pump tipping or falling.

Death or serious injury can occur.



Fasten the lantern (200) to secure the
pump.

CAUTION

Risk of fingers being trapped.

Minor injuries can occur.



Do not reach in between connections.



Assemble the lantern (200) on the base
plate (GPU).



Clean the flange bearing surfaces (FLS),
bolt circle (ZD) and output shaft of the
drive (ANT).



Joint (G) reassembly note rotating unit - in-
dividual parts (chapter 9.2).

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды