Seepex BN 100-6LS Скачать руководство пользователя страница 42

Страница: 42 / 70

Ausgabe
issue

D / 04.02.2013

Dokument
document

OM.SCT.02e

Blatt
sheet

14 (18)

Dismantling/reassembly

9.1.4.6 Segment retainer (671), pressure branch (700) – pre-assembly

9.1.4.7 Pressure branch (700) – Reassembly

9.1.4.8 Stator (601) – Reassembly



Remove contaminants such as paint and
corrosion from all seal faces/centring re-
cesses (ZA).



Coat O-ring (731) with soft soap.



Insert the O-ring (731) into the centring re-
cess on the suction casing (ZA, 500).



Assemble the segment receiver (671) on
the pressure branch (700) and align it
using a spirit level.



Observe the segment order.

–

* = A-A, B-B, C-C, D-D



Prop up the rotor with lining plate (S).



Align the pressure branch (700)/lantern
(200) axially and radially on the base plate
(GPU).

–

If necessary, undo the connection to
the base plate (GP).

–

Use at least 2 adjusting segments
(635) opposite each other for the
alignment. To secure, gently tighten
the hexagon nuts (639).



Assemble the pressure branch (700)/lan-
tern (200) on the base plate (GPU).



Remove adjusting segments (635).



For easier assembly, moisten sealing surfaces, geometry of the stator halves and rotor
with soft soap.

–

Do not moisten the outer surfaces of the stator with soft soap.

NOTICE

Coating the stator outer surfaces

Damage to property can occur



Remove any coating on the stator outer surfaces.



Coat only the stator internal surfaces.

Содержание BN 100-6LS







































































Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды

Seepex BN 100-6LS, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BN 100-6LS

Отзывы:

Похожие инструкции для BN 100-6LS

Бренды по названию

Популярные бренды