Seastar Solutions i7700 Скачать руководство пользователя страница 13

Страница: 13 / 60

3-1

i7700 Installation Supplement, Rev. B

To assist with the installation and maintenance of this Electronic Shift

and Throttle system SeaStar Solutions recommends that:
• Installation MUST be performed by a SeaStar Solutions

authorized installer.

• Read and understand ALL installation manuals before starting

the installation process. Knowing the correct order of installation

and location of components will drastically reduce installation

time as well as prevent common installation errors.

• Read and understand ALL Safety Information that is noted in this

manual and ALL other Installation Manuals.

If any problems are found before, during or after the installation of the

steering system, please contact Technical Support for assistance:

Technical Support

Web: www.seastarsolutions.com
E-mail: [email protected]
Phone: 604.248.3858
Fax: 604.279.2202

3.1 Important Information/Technical

Support Contact

3.0 INSTALLATION

Mount the control head on the dash in an area which will allow for

convenient access during use. Whenever possible, it should be

mounted in a location to minimize water spray. Ensure that the control

handle(s) can be moved throughout the complete range of motion in

both forward and reverse without interference. ABYC standard P-14

calls for a minimum of 2-1/2" (64 mm) clearance between the

control lever and the steering wheel rim under all possible lever and

wheel positions.
The control head requires one of the dash cutout templates in

Appendix A.

Control Head Trim Switch Connection (Optional)

The control head includes a single trim/tilt switch on the end of the

port handle. This switch can be wired to provide synchronous trim/

tilt control of all engines. If independent trim/tilt is desired use tilt/

trim kit HA5491 (for twin engine configurations) and connect the

wiring as shown in Figure 3-1.

3.2 Installing the Control Head

3.2.1

Содержание i7700





























































Результаты поиска

Содержание i7700

Отзывы:

Похожие инструкции для i7700

Бренды по названию

Популярные бренды

Seastar Solutions i7700, Руководство по установке

Результаты поиска

Содержание i7700

Отзывы:

Похожие инструкции для i7700

Бренды по названию

Популярные бренды