Seastar Solutions i7700 Скачать руководство пользователя страница 54

Страница: 54 / 60

D-2

i7700 Installation Supplement, Rev. B

The current firmware version installed in a component can be checked

through Datalink.

NOTE:

When opening component windows in Datalink, it is good

practice not to have more than two components open at a time to

avoid potential communication errors.

D.1 Checking Component Firmware

Revision Levels

Figure D-2. Datalink workspace.

Using DATALINK
1.

Connect the computer to the i7700 system as shown in section

C.2.

In the ‘Interfaces’ section in Datalink, click on the box to expand

the component information. See figure D-2. (In an i7700 system

you will see only the Control Head(s) and Actuators in the

component list.)

Firmware revision can be found under the ‘Firmware Part

Number’ field.

D.1.1

FIRMWARE

REVISION

DATALINK

VERSION

CLICK TO EXPAND

COMPONENT

INFORMATION

Содержание i7700





























































Результаты поиска

Содержание i7700

Отзывы:

Похожие инструкции для i7700

Бренды по названию

Популярные бренды

Seastar Solutions i7700, Руководство по установке

Результаты поиска

Содержание i7700

Отзывы:

Похожие инструкции для i7700

Бренды по названию

Популярные бренды