Sculpt SEGUIN MULTIVISION HYDRO 80 Скачать руководство пользователя страница 16

Страница: 16 / 47

3. COMPONENTS LIST

IMPORTANT

This components list details the amount of flue supplied (by the retailer) according to unit and minimum

flue kit requirements. For correct use please ensure you are referring to your installation kit type. For any

questions in relation to the supplied components contact your local retailer. Each unit is supplied with a

ducting kit consisting of; one metal register and one duct (4 Zero Type: aluminium inner core, aluminium

outer, poly insulated, minimum RI.0) by the retailer.
Sculpt Fireplace Collection bears no liability to the functioning and supply of these components.

Additional components required for installation are the responsibility of the retailer and (or) installer.

900MM STAINLESS FLUE - 250MM DIAMETER (ACTIVE)

900MM GALVANISED FLUE - 300MM DIAMETER (INSULATING OUTER)
900MM GALVANISED FLUE - 350MM DIAMETER (INSULATING OUTER)

WIND RIM COWL TO SUIT

5
4
4
1

COMPONENTS

QUANTITY

4.5M INBUILT TRIPLE SKIN FLUE KIT - SEGUIN MULTIVISION HYDRO 80

900MM STAINLESS FLUE - 250MM DIAMETER (ACTIVE)

900MM GALVANISED FLUE - 300MM DIAMETER (INSULATING OUTER)

WIND RIM OPTION B COWL TO SUIT

5
1

*Double skin black flue to be dependant on ceiling height, ascertained by the retailer.

COMPONENTS

QUANTITY

4.5M INBUILT CHIMNEY FLUE KIT - SEGUIN MULTIVISION HYDRO 80

900MM STAINLESS FLUE - 250MM DIAMETER (ACTIVE)

900MM BLACK GALVANISED FLUE - 300MM DIAMETER (INSULATING OUTER)

900MM GALVANISED FLUE - 300MM DIAMETER (INSULATING OUTER)
900MM GALVANISED FLUE - 350MM DIAMETER (INSULATING OUTER)

BLACK DROPPER BOX AND CEILING RING TO SUIT

WIND RIM OPTION B COWL

2
2
1
1

COMPONENTS

QUANTITY

4.5M FREE STANDING BLACK FLUE KIT - SEGUIN MULTIVISION HYDRO 80

Содержание SEGUIN MULTIVISION HYDRO 80
















































Результаты поиска

Содержание SEGUIN MULTIVISION HYDRO 80

Отзывы:

Похожие инструкции для SEGUIN MULTIVISION HYDRO 80

Бренды по названию

Популярные бренды

Sculpt SEGUIN MULTIVISION HYDRO 80, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SEGUIN MULTIVISION HYDRO 80

Отзывы:

Похожие инструкции для SEGUIN MULTIVISION HYDRO 80

Бренды по названию

Популярные бренды