Sculpt SEGUIN MULTIVISION HYDRO 80 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 47

background image

28

4.3

SKAMOTEC INSTALLATION

SKAMOTEC can be purchased from any Sculpt Fireplace Collection retailer or installer.

.

SKAMOTEC 225 is a light weight material providing several advantages- excellent R-value, high mechanical

strength, low thermal conductivity and maximum service temperatures of 1000 C°. The exceptional heat resistance

makes SKAMOTEC 225 able to withstand continuous heat cycles to full service temperature limit and the low

thermal conductivity provides maximum insulation throughout the temperature range making it the ideal product

when building custom fireplace enclosures.*

PLEASE REFER TO SKAMOTEC 225 INSTALLATION MANUAL

ONLINE VIDEO

SKAMOTEC 225 - BUILDING BOARD FOR FIREPLACE ENCLOSURES

(VISIT YOUTUBE.COM)

PLEASE NOTE THAT A SKAMOTEC ENCLOSURE/CAVITY IS NOT CONSIDERED A MASONRY ENCLOSURE/CAVITY. PLEASE REFER TO
AUSTRALIAN & NEW ZEALAND STANDARDS AS/NZS 2918/2014

*Referenced from skamol brochure ”skamotec 225 building board for fireplace enclosures”, all rights reserved.

«
...
26
27
28
29
30
...
»

Содержание SEGUIN MULTIVISION HYDRO 80
















































Отзывы:

Нет отзывов

Похожие инструкции для SEGUIN MULTIVISION HYDRO 80

Бренд: Majestic fireplaces Страницы: 28

Бренд: Majestic Страницы: 24

Бренд: Majestic Страницы: 44

Бренд: Majestic Страницы: 7

Southern Series

Бренд: Warmington Страницы: 2

Бренд: Quadra-Fire Страницы: 36

Бренд: Quadra-Fire Страницы: 56

Бренд: Vermont Castings Страницы: 28

Бренд: Napoleon Страницы: 40

Бренд: Heat-N-Glo Страницы: 53

Бренд: barbas Страницы: 32

Бренд: Hearth & Home Страницы: 24

Бренд: Backyard Creations Страницы: 4

Бренд: Dimplex Страницы: 22

Бренд: Heat&Glo Страницы: 49

Бренд: Spark modern fires Страницы: 43

Бренд: Lennox Hearth Products Страницы: 24

Бренд: True North Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды