Sculpt SEGUIN MULTIVISION HYDRO 80 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 47

background image

43

TESTING LABORATORY
MANUFACTURER
MODEL
ISSUE DATE
INVESTIGATING OFFICE
RESULTS

CONCLUSION

HRL Technology
Seguin Duteriez
Multivision 8000
02.11.2015
Steve Marland
Testing of the maximum power (kW) output of the Multivision 8000
solid fuel appliance was performed at the high burn rate prescribed
in ASNZS4013 (2014) on the 2nd of November 2015. The appliance
produced a maximum Heat output of 25.9kW
Exemption from testing the Multivision 8000 solid fuel appliance
should be claimed under section 1.2.3 (b) of AS/NZS4013 (2014) as the
maximum heat output from combustion is greater than 25kW when fired
at the prescribed high burn rate and that the appliance is intended for
space heating by means of transferring heat to the living area by ducted
hot air.

MULTIVISION 8000 APPLIANCE POWER OUTPUT TEST

8. TEST RESULTS

TEST REPORTS

«
...
41
42
43
44
45
...
»

Содержание SEGUIN MULTIVISION HYDRO 80
















































Отзывы:

Нет отзывов

Похожие инструкции для SEGUIN MULTIVISION HYDRO 80

Бренд: Valcourt Страницы: 100

Бренд: Valcourt Страницы: 53

FP-7-LM ANTOINETTE

Бренд: Valcourt Страницы: 56

Бренд: Valcourt Страницы: 62

Бренд: Jet-Line Страницы: 6

Бренд: Vermont Castings Страницы: 28

Бренд: Jøtul Страницы: 104

Бренд: Bold Flame Страницы: 20

Бренд: Fondis Страницы: 33

Бренд: QOMOTOP Страницы: 10

Бренд: Procom Страницы: 26

L-CM057PST-B-CA

Бренд: Sunjoy Страницы: 4

Nestor Martin 023

Бренд: Euroheat Страницы: 32

Бренд: Kingsman Страницы: 59

Бренд: Magiglo Страницы: 56

STONEFIRE SF10BL

Бренд: Valor Страницы: 20

Бренд: JC BORDELET Страницы: 15

Бренд: bhp Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды