Schilling Megalight Скачать руководство пользователя страница 6

Страница: 6 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

YMBOLS RELATED TO DEVICE SAFETY

Symbol

Meaning

INDICATION: this symbol indicates that in this position the device
power switch is off

INDICATION: this symbol indicates that in this position the device
power switch is on

GENERIC WARNING: (caution, warning, danger): this symbol
indicates that the instructions regarding important manoeuvres or

maintenance operations need to be carefully read.

ELECTRICITY WARNING: this symbol indicates the presence of
associated dangerous voltage, or powerful enough to constitute an

electrical risk. This symbol must appear on the finished machine as
well, at the electrical risk area.

LASER WARNING: this symbol indicates the danger of exposure to
visible or invisible laser radiation. This symbol must appear on the

finished machine as well, at the optical risk area.

FIRE WARNING: this symbol indicates the danger of a fire when
processing flammable materials. For this reason it is necessary to

follow the instructions provided by the manufacturer when
commissioning the machine.

CONFORMITY: this symbol indicates that the device has been
produced in conformity with European Community directives.

READ THE WARNING: this symbol indicates that it is obligatory to
read the important remarks in the manual before continuing

TEMPERATURE WARNING: this symbol indicates the presence of

high temperatures which may involve a risk of being burned

Содержание Megalight


































































Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды

Schilling Megalight, Руководство пользователя

Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды