Schilling Megalight Скачать руководство пользователя страница 16

Страница: 16 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

The rear management panel faces the side opposite the operator and includes the following
elements:

1 Socket for 230/110 Vac – 3/6A – 50/60Hz mains supply

2 Main

switch to disconnect from the mains

3 Protection

fuses (5x20mm, 6.3A/250V type T)

4 Galvo

Supply

connector (sub-D, 9 p., male) for Scanner Head power

Internal Interlock Connector (DIN, 3 p., male) for connection to an external
emergency interlocks circuit.

6 Aiming

Beam connector (SMB, female) for connecting the red aiming diode.

Command Box connector (sub-D, 25 p., female) for connection to an external

command box.

P.C. connector (sub-D, 9 p., female) for connecting the device to the DSp2 contained

in the external Personal Computer.

Slave Out connector (sub-D, 15 p., female) (not used in this version).

10 Optical Fibre connector (D-80-LKA) for the optical fibre connection between the

Rack and Resonator.

11 R.F. connector (not used in this version).

12 Cooling fan

Содержание Megalight


































































Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды

Schilling Megalight, Руководство пользователя

Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды