Schilling Megalight Скачать руководство пользователя страница 26

Страница: 26 / 65

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

Edition 2004

Picture 10: Layout of connection wires

Electrical connections

The sequence of the electrical connections involves the following phases:

•

Make sure the main switch MS is in the OFF position.(

)

•

Connect the DL wire between the AIMING BEAM connector (6) of the rear Management

Panel of the power supply box and the SMB socket located on the laser head body.

•

Connect the TS cable between the GALVO SUPPLY connector (4) of the rear
Management Panel of the power supply box and the SUB D 9 pin M connector on the
scanner head.

•

Connect the STS wire between the SUB-D 25 pole F connector of the DSP board and

SUB-D 25 pin F connector located on the Scanner Head;

•

Connect the PC wire between the PC connector (8) of the rear Management Panel of the
power supply box and the DB 9 pin F connector on the DSP board.

•

Connect the power supply wire (1) of the rear Management Panel.

•

Connect the monitor, mouse and keyboard to the related connectors on the PC.

STS

OPTICAL
FIBER

Содержание Megalight


































































Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды

Schilling Megalight, Руководство пользователя

Результаты поиска

Содержание Megalight

Отзывы:

Похожие инструкции для Megalight

Бренды по названию

Популярные бренды