Schilling Megalight Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 65

background image

Schilling Marking Systems GmbH

In Grubenäcker 1 DE-78532 Tuttlingen

+49 (0)7461 9472-0

+49 (0)7461 9472-20

[email protected]

www.schilling-marking.de

MegaLight

Installation

Technical modifications reserved

22

Edition 2004

CHAPTER 2:

INSTALLATION and START-UP

Preliminary installation notes

This chapter discusses the subjects related to the installation procedure for the MEGALIGHT™
device and the tests to safely start it.
Installation must be effected by TRAINED AND QUALIFIED personnel because it

involves effecting electrical and optical tests which require a specific qualification.
Warning: before installing the device carefully read Appendix C, Safety Notes, related to the

main standards regarding Class I laser devices containing Class IV sources.

WARNING:

The mains voltage is dangerous. If adequate precautions are not taken it can
cause electric shock! To avoid the electrical risk do not use connection wires,

plugs, sockets or extension cords lacking a quality mark or which are not intact.

N.B.:
Before continuing with installation the device makes sure you have suitable

goggles available for protection against scattered laser radiation. Even with
goggles, it is possible to damage your vision by viewing direct laser radiation!

WARNING:
Before continuing with installation make sure that the environment is suitable

for the intended use. In particular make sure there are no openings (windows or
other) towards the outside which can let dangerous radiation leak out!

WARNING:

Install the laser on a stationary support. Unforeseen risks may be caused if the
device falls!

WARNING:
Only use original wires, connectors and optical fibres. Wires with an incorrect

dimension of loose connections can cause an electrical shock or a fire.

WARNING:
Do not bend the optical fibre beyond the minimum radius indicated. Greatly

bending the fibre may cause unforeseen optical risk.

«
...
20
21
22
23
24
...
»

Содержание Megalight


































































Отзывы:

Нет отзывов

Похожие инструкции для Megalight

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

Бренд: Kawai Страницы: 5

Бренд: Jata hogar Страницы: 12

Бренд: LaMotte Страницы: 2

Stage Piano MP8

Бренд: Kawai Страницы: 70

Бренд: VELOCICALC Страницы: 10

Бренд: Energic Plus Страницы: 12

Бренд: Ramsey Electronics Страницы: 40

Бренд: TAC Страницы: 28

Бренд: Omega Страницы: 22

Бренд: Camlab Страницы: 28

Бренд: D-tect Systems Страницы: 28

Бренд: Feasa Страницы: 145

BlueForce Smart

Бренд: CAME Страницы: 24

Бренд: ERICHSEN Страницы: 33

Бренд: sewerin Страницы: 134

Quantumdata 780E

Бренд: Teledyne Lecroy Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды