Schaeff Echo 3000 Скачать руководство пользователя

Страница: 88 / 92

Replace traction motor.

Bad traction motor (open winding).

Replace traction amplifier.

Bad traction amplifier.

Check cables, repair or replace.

Broken or loose F1 or F2 cable from traction
amplifier to traction motor.

PERFORM OUTPUT TEST 17 or 18 - TRACTION MOTOR FIELD & ARMATURE CURRENT. Should
see Field amps 25-36 and armature amps 40-70 with truck jacked up. Test both forward and reverse.
Left and right field current should not differ by more than 5 amps.

Solution

Possible Cause

The system controller detects no current to the
traction motor field when there should be.

TRACTION system shutdown. Will not pass
POST.

Criteria

Resulting Effect

LEFT/RIGHT TRACTION MOTOR FIELD CURRENT NOT PRESENT

Fault condition

E63L

E63R

Replace traction motor.

Bad traction motor (shorted winding).

Replace traction amplifier.

Bad traction amplifier.

Test diode and replace if necessary.

Bad diode.

Check cables, repair or replace.

Shorted A1 or A2 cable from traction amplifier to
traction motor.

Solution

Possible Cause

The traction motor armature current draw is greater
than the system controller expects.

TRACTION system shutdown. Will not Pass
POST.

Criteria

Resulting Effect

LEFT/RIGHT TRACTION MOTOR ARMATURE HIGH

Fault condition

E64L

E64R

lectric

ounterbalance

igh

utput

Troubleshooting

REV 12/5/99

TS.13

Содержание Echo 3000





























































































Результаты поиска

Содержание Echo 3000

Отзывы:

Похожие инструкции для Echo 3000

Бренды по названию

Популярные бренды

Schaeff Echo 3000, Руководство по обслуживанию

Результаты поиска

Содержание Echo 3000

Отзывы:

Похожие инструкции для Echo 3000

Бренды по названию

Популярные бренды