Schaeff Echo 3000 Скачать руководство пользователя

Страница: 83 / 92

Replace system controller field fix.

Malfunction of the horn driver.

Replace horn.

Horn is open or shorted internally.

Check 15 amp fuse on main harness, wiring on all
hydraulic valve coils, repair or replace. Check for
B+ at J4 Pin 3.

If error codes 29-42 occur at the same time; 15
Amp fuse in main harness is bad.

Check and repair damaged wires to the horn.

Broken or shorted wiring to the horn.

PERFORM OUTPUT TEST 15 - HORN.

Solution

Possible Cause

The horn circuit is overheated, shorted to supply,
shorted to ground, or disconnected.

DISPLAY code.

Criteria

Resulting Effect

HORN WIRING FAULT

Fault condition

E32

Replace system controller field fix.

Malfunction of the coil driver.

Replace coil.

Solenoid coil is open or shorted internally.

Check 15 amp fuse on main harness, wiring on all
hydraulic valve coils, repair or replace. Check for
B+ at J4 Pin 3.

If error codes 29-42 occur at the same time; 15
Amp fuse in main harness is bad.

Check and repair damaged wires to the coil.

Broken or shorted wiring to the coil.

PERFORM OUTPUT TEST 06 - TILT FORWARD SOLENOID.

Solution

Possible Cause

The tilt forward valve solenoid coil circuit is
overheated, shorted to supply, shorted to ground, or
disconnected.

LIFT system shutdown.

Criteria

Resulting Effect

TILT FORWARD VALVE WIRING FAULT

Fault condition

E33

lectric

ounterbalance

igh

utput

Troubleshooting

REV 12/5/99

TS.8

Содержание Echo 3000





























































































Результаты поиска

Содержание Echo 3000

Отзывы:

Похожие инструкции для Echo 3000

Бренды по названию

Популярные бренды

Schaeff Echo 3000, Руководство по обслуживанию

Результаты поиска

Содержание Echo 3000

Отзывы:

Похожие инструкции для Echo 3000

Бренды по названию

Популярные бренды