SBC PCD7.L79 Series Скачать руководство пользователя страница 51

Страница: 51 / 72

Saia-Burgess Controls AG

Manual for PCD7.L79xN room controllers

│

Document 27 / 602

N02 │ 2013-11-27

Registers, configuration

5-1

Register usage

This section describes the register usage on the compact room controllers. Detailed

knowledge of this is not required to use the FBoxes. Rather, the section is aimed at

interested persons and programmers.

5.1

Registers, configuration

(* = EEPROM parameters)

Registers

Description

Communication

14*

S-Bus telegrams, defines a minimum time for the compact room controller to wait

before responding to a request telegram from the master. Unit: [ms/2000]

Range: 100

…

2300 default: 2000

15*

S-Bus baudrate; as the controller works with automatic baudrate detection, this

parameter has no effect in practice.

(73=4

800; 36=9

600; 18=19 200; 9=38 400; 21=115 200)

Communication watchdog register.

255

no monitoring

Stop/restart control

(Function dependent on configuration of register 112)

1...254 Counter decremented by 1 for every program cycle (20 s). The S-Bus master has

to load the register on a cyclical basis.

(Where the value "1" is entered, the controller will stop/restart in max. 20 seconds)

Time, in 20-second steps, during which a further S-Bus station address 252 is

activated. The time is initialised to 15 minutes by operating the service pin. Every

successful communication within the period restarts the time for another 15

minutes. When the counter runs down to 0 or the register is manually set to 0,

address 252 is deactivated again.

110

S-Bus station address

111

Active RS-485 Bus connection.

RS-485 leads must be connected as lines. Stubs are not allowed, and both ends

of the line must be "closed off" with a resistor (approx. 150 Ω) between strands D

and /D.

The best signal quality is achieved with an active Bus connection with a resistor

b5V and GND.

+5 V

/RX-/TX

RX-TX

PCD1/2.Mxxx

Socket A

Pull up

330 Ohm

Pull down

330 Ohm

Segment lenght max. 1200 m

max. 32 stations

Termination

Resistor

150 Ohm

The active Bus connection is switched on and off via the Configuration register.

No Bus connection (default setting)

Active Bus connection enabled

Содержание PCD7.L79 Series









































































Результаты поиска

Содержание PCD7.L79 Series

Отзывы:

Похожие инструкции для PCD7.L79 Series

Бренды по названию

Популярные бренды

SBC PCD7.L79 Series, Руководство пользователя

Результаты поиска

Содержание PCD7.L79 Series

Отзывы:

Похожие инструкции для PCD7.L79 Series

Бренды по названию

Популярные бренды