SYSTEEMVEREISTEN
64 RW-470 PLOTBASE Installation
Tip
: De taalinstelling tijdens de installatie geldt alleen voor het installeren zelf. Als u de taal voor de volledige
RW-470-software wilt wijzigen, moet u dat doen via de landinstellingen van de systeembesturing van
Windows. De handleiding hiervoor vindt u in Windows-handboeken.
Systeemvereisten
Lees de volgende adviezen aandachtig door. Deze kunnen zeer nuttig zijn om de optimale hardware voor uw wensen
te vinden.
•
Besturingssysteem
:
Microsoft Windows 2000 Professional met ServicePack 1 of hoger
•
Processor
:
Pentium III, minstens 800 Mhz
•
Frontside-bus:
133 Mhz
•
PCI-bus:
Het PCI-bussysteem moet beantwoorden aan de huidige standaard (PCI 2.0 of hoger - 3.3 of 5 V autoadaptieve,
maximale lading 5 A). Wanneer uw computer niet aan deze standaard voldoet, is het mogelijk dat de plotter-
controller niet wordt herkend.
•
Systeemgeheugen
:
Gebruik een systeemgeheugen met minstens 256 MB RAM. Met dit systeemgeheugen kunt u de tekeningen in hun
maximale grootte plotten of scannen. Wanneer u echter tekeningen in hun maximale grootte simultaan wilt plotten
en scannen, wordt een systeemgeheugen van 512 MB RAM aanbevolen. Het simultaan scannen en plotten van
kleinere formaten maakt het gebruik van een kleiner systeemgeheugen ook mogelijk. Neem voor meer
bijzonderheden contact op met uw leverancier of support-technicus.
•
Harde schijf
:
De harde schijf moet de beschikking hebben over minimaal 10 GB. Wij adviseren u om de software niet op het
schijfstation te installeren waarop u het besturingssysteem hebt geïnstalleerd.
•
Cd-diskdrive
•
Netwerkinterface/Configuratie
:
10/100-Base T Ethernet, de TCP/IP-configuratie is beslist noodzakelijk.
•
RW-470 controller:
fysische grootte: 190 mm x 128 mm
PCB buitenafmetingen: 174,63 mm x 106,8 mm
•
Monitor:
een resolutie van minimaal 1024 x 768 pixels
Controller Board Type 470
De RW-470-software functioneert alleen, wanneer u een controller voor de plotter hebt geïnstalleerd. Installeer
hiervoor het Controller Board Type 470 en de erbij horende software.
Installatie Controller Board Type 470
Tip
: Het Controller Board Type 470 kan door elektrostatische lading worden beschadigd. Haal daarom de
controller voorzichtig uit de verpakking en pak deze uitsluitend aan de randen of aan de buitenste houders
vast. Raak de bedrading indien mogelijk nooit met de vingers aan. Wanneer dit toch onvermijdelijk is, raak
dan van tevoren eerst een ander metalen voorwerp aan om een eventueel aanwezige statische lading af te
leiden.
1. Schakel eerst de computer uit, voordat u de controller installeert.
2. Kies een vrije PCI-insteekkaartplaats. Houdt er rekening mee, dat op sommige computers de PCI-aansluiting nr. 5
niet overeenkomt met de PCI-standaards 2.0. Gebruik in een dergelijk geval insteekkaartplaats nr. 1 tot 4.
3. Breng de controller in de PCI-aansluitbus aan en draai de bevestigingsschroef vast. Controleer of de controller juist
is bevestigd, geen delen ervan naburige kaarten of de behuizing aanraken en of de bevestigingsschroef wel goed
vast zit.
Содержание RW-470 Clients
