REQUISITOS DEL SISTEMA
40 RW-470 PLOTBASE Installation
Nota: El ajuste del idioma durante la instalación tiene validez sólo para la operación de instalación. Si Vd.
quiere cambiar el idioma para todo el software del RW-470, lo tendrá que hacer por los ajustes de los
países del control del sistema de Windows. Instrucciones al respecto se proporcionan en los Manuales de
Windows.
Requisitos del sistema
Lea atentamente las siguientes recomendaciones. Éstas pueden ser muy útiles para encontrar el óptimo hardware que
se ajuste a sus necesidades.
•
Sistema operativo
:
Microsoft Windows 2000 Professional con ServicePack 1 o o mayor
•
Procesador:
Pentium III, 800 MHz o más alto
•
Bus Front Side:
133 MHz
•
Bus PCI:
El sistema de bus PCI tendrá que corresponder al estándar actual (PCI 2.0 o más alto – 3.3 V ó 5 V autoadaptivo,
carga máxima 5 A). Si su ordenador no satisface este estándar, entonces el controlador de la trazadora de gráficos
posiblemente no podrá ser detectado.
•
Memoria del sistema
:
Utilice una memoria del sistema con una RAM de mínimo 256 MB de capacidad. Con esta memoria del sistema
podrá trazar o escanear el tamaño máximo de los dibujos. No obstante, si Vd. desea trazar y escanear simultá-
neamente dibujos con el máximo tamaño, se le recomienda una memoria RAM del sistema de 512 MB. El esca-
neado y el trazado simultáneos de formatos más pequeños permite también utilizar una memoria más pequeña
del sistema. Para mayores detalles, diríjase por favor a su vendedor o al técnico de asistencia.
•
Disco duro
:
El disco duro debería disponer de una capacidad mínima de almacenamiento superior a los 10 GB. Le recomen-
damos no instalar el software en la unidad de disco en la que ha instalado Vd. el sistema operativo.
•
Interfaz de red
:
10/100-Base T Ethernet, la configuración TCP/IP es absolutamente necesaria.
•
RW-470 Controller:
Tamaño físico: 190 mm x 128 mm
Dimensiones PCB: 174,63 mm x 106,8 mm
•
Pantalla:
Con una resolución mínima de 1024 x 768 pixeles
Controller Board tipo 470
El software RW-470 funciona sólo si Vd. ha instalado un Controller para la trazadora de gráficos. Para esto tendrá
que instalar el Controller Board tipo 470 y el respectivo software.
Instalación del Controlller Board tipo 470
Nota: El Controller
Board tipo 470 puede ser dañado debido a una carga electrostática. Por tal razón,
extraiga cuidadosamente el Controller del embalaje y cójalo sólo por los bordes o los fijadores exteriores.
No toque nunca los circuitos con los dedos. No obstante, si esto es necesario, toque primeramente un objeto
metálico para desviar una posible carga estática.
1. Desactive su ordenador antes de instalar el Controller.
2. Elija un zócalo de conexión PCI libre. Tenga en cuenta que en algunos ordenadores la conexión PCI No. 5 no
coincide con los estándares PCI 2.0 En tal caso, utilice los zócalos de conexión No. 1 hasta 4.
3. Enchufe el Controller en la hembrilla de conexión PCI y apriete a fondo el tornillo de sujeción. Pruebe si el
Controller está correctamente sujetado, que no tenga contacto con componentes de tarjetas adyacentes o con la
carcasa y que el tornillo de sujeción esté bien apretado.
4. Arranque de nuevo el ordenador. Una los cables con la trazadora de gráficos.
Содержание RW-470 Clients
