manualshive.com logo in svg

Satec PM171 series, Справочное руководство

Поделиться
Скачать
Satec PM171 series Скачать руководство пользователя страница 35

34

Table 5-38  Digital Inputs Identifiers 

Discrete input 

ID 

Not allocated 

    0 

Digital input # 1 

    1 

Digital input # 2 

    2 

5.18  Log Memory Partitions Setup Registers 

Table 5-39  Memory Partitions Setup Registers 

Partition 

Number 

Memory partition 

Setup registers  

(see Table 5-40) 

0 Event 

log  3660-3665 

1 

Data log #1 

3668-3673 

2 

Data log #2 

3676-3681 

3 

Data log #3 

3684-3689 

4 

Data log #4 

3692-3697 

5 

Data log #5 

3700-3705 

6 

Data log #6 

3708-3713 

7 

Data log #7 

3716-3721 

8 

Data log #8 

3724-3729 

 

Table 5-40  Partition Setup Registers 

Parameter 

Offset

Size, 

byte

Direction 

Range 

The number of records in the 
partition 

+0 2 R/W 

0-65535, 
0 = delete partition 

The number of log parameters in the 
record for a data log partition (for an 
event log partition, write 0) 

+1 2 R/W 

0-16 

Partition type 

+2 

2 

R/W 

0 = non-wrap 
1 = wrap around 

Record size, byte 

+3 

2 

R 

 

Partition size, byte 

+4 
+5 

4 R 

0-524288 

 
These registers allow you to allocate a memory partition for logging and to specify the partition size and type. 
Before allocating a partition, it is recommended to check the available memory by reading the extended memory 
status registers. To help you in planning memory, Table 5-41 shows the record size for each partition. 
 
Note that the existing partition may not be resized. To change the partition properties, you should first delete a 
partition and then reallocate it with the desirable properties. To delete a partition, write zero into the first 
partition's register. 
 
When allocating a memory partition, all partition registers must be written at once using a single request. After 
reallocation of memory, the instrument performs the memory optimization and will not respond to the host 
requests for approximately 1 second per 128 Kbyte of memory. 
 
Writing into registers at o3, +4 and +5 does not affect the register contents. No error will occur. 
 

Table 5-41  Partitions' Record Size 

Partition  

Record size, byte 

Event log 

14 

Data log 

8 + 4 

∗

 (NUMBER OF PARAMETERS) 

 

Содержание PM171 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды