Satec PM171 series Скачать руководство пользователя страница 33

Страница: 33 / 43

Trigger parameter

Trigger Size,

Unit

Limit/scale

Con-

byte

Low

High

version

High sliding window kVA demand (E)

5643

1kVA

Pmax

LIN3

High accumulated kW import demand (E)

5647

1kW

Pmax

LIN3

High accumulated kVA demand (E)

5649

1kVA

Pmax

LIN3

High predicted kW import demand (E)

5650

1kW

Pmax

LIN3

High predicted kVA demand (E)

5652

1kVA

Pmax

LIN3

For parameter limits, see note

to Table 5-1

Voltages are transmitted in 1V units, currents in 1 A units, and powers in 1 kW/kvar/kVA units.

The setpoint is operated when the actual phase sequence does not match the indicated phase rotation.

The actual frequency range is 45.00 - 65.00 Hz (20.00 - 65.00 Hz - special order).

When the 4LN3 or 3LN3 wiring mode is selected, the voltages will be line-to-neutral; for any other wiring

mode, they will be line-to-line voltages.

(E) available in the PM171E

Table 5-30 Setpoint Actions

Action

Action ID

No action

Operate relay #1

12288

Operate relay #2

12289

Increment counter #1 (E)

16384

Increment counter #2 (E)

16385

Increment counter #3 (E)

16386

Increment counter #4 (E)

16387

Clear counter #1 (E)

16896

Clear counter #2 (E)

16897

Clear counter #3 (E)

16898

Clear counter #4 (E)

16899

Clear all counters (E)

25600

Reset total energy (E)

24576

Reset all total maximum demands (E)

24832

Reset power maximum demands (E)

24833

Reset volt/ampere maximum demands (E)

24834

Reset TOU energy (E)

25088

Reset TOU maximum demands (E)

25344

Clear Min/Max registers (E)

25856

Event log (E)

28674

Data log #1 (E)

28928

Data log #2 (E)

28929

Data log #3 (E)

28930

Data log #4 (E)

28931

Data log #5 (E)

28932

Data log #6 (E)

28933

Data log #7 (E)

28934

Data log #8 (E)

28935

(E) available in the PM171E

In the PM171E, operate/release actions via relays are automatically recorded to the event log whenever an

electrical quantity, status input, or phase reversal trigger is used.

Either setpoint transition (both operate and release) is recorded to the event log.

5.15 Pulsing Setpoints Registers

Table 5-31 Pulsing Registers

Relay

Setup registers (see Table 5-32)

Relay #1

2892-2893

Relay #2

2894-2895

Содержание PM171 series












































Результаты поиска

Содержание PM171 series

Отзывы:

Бренды по названию

Популярные бренды

Satec PM171 series, Справочное руководство

Результаты поиска

Содержание PM171 series

Отзывы:

Бренды по названию

Популярные бренды