manualshive.com logo in svg

Satec PM171 series, Справочное руководство

Поделиться
Скачать
Satec PM171 series Скачать руководство пользователя страница 30

29

 

5.12  Digital Inputs Allocation Registers 

Table 5-24  Digital Inputs Allocation Registers 

Parameter 

Register  Size,

byte

Direction

Range 

Status inputs allocation mask  

3292 

2 

R 

 See 

Table 

5-25 

Pulse inputs allocation mask  

3293 

2 

R/W 

See Table 5-25 

Not used  

3294 

2 

R 

 

Read as 0 

External demand synchronization input mask (E)

3295 

2 

R/W 

See Table 5-25 

  Writing to these locations is ignored. No error will occur.  

(E)  available in the PM171E 

NOTES  

1.  

All digital inputs that were not allocated as pulse inputs will be automatically configured as status inputs. 

2.   A digital input allocated for the external demand synchronization pulse or time synchronization pulse 

will be automatically configured as a pulse input.  

 

Table 5-25  Digital Inputs Allocation Mask 

Bit  

Description 

0 

Digital input # 1 allocation status 

1 

Digital input # 2 allocation status 

2-15 

Not used (read as 0) 

Bit meaning: 0 = input is not allocated, 1 = input is allocated to the group 

5.13  Timers Setup Registers 

Table 5-26  Timers Setup Registers 

Parameter 

Register  Size, 

byte 

Direction Range 

Timer #1 time interval  3300 

2 

R/W 

1-9999 sec, 0 = timer disabled 

Timer #2 time interval  3301 

2 

R/W 

1-9999 sec, 0 = timer disabled 

 

5.14  Alarm/Event Setpoints Registers 

Table 5-27  Setpoint Registers 

Setpoint  

Setup registers (see Table 5-28) 

Setpoint #1 

352-395 

Setpoint #2 

396-439 

Setpoint #3 

440-483 

Setpoint #4 

484-527 

Setpoint #5 

528-571 

Setpoint #6 

572-615 

Setpoint #7 

616-659 

Setpoint #8 

660-703 

Setpoint #9 

704-747 

Setpoint #10 

748-791 

Setpoint #11 

792-835 

Setpoint #12 

836-879 

Setpoint #13 

880-923 

Setpoint #14 

924-967 

Setpoint #15 

968-1011 

Setpoint #16 

1012-1055 

 

Содержание PM171 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды