manualshive.com logo in svg

Satec PM171 series, Справочное руководство

Поделиться
Скачать
Satec PM171 series Скачать руководство пользователя страница 31

30

Table 5-31  Setpoint Setup Registers 

           Parameter       

Offset 

Size, byte

Range 

Trigger ID 

+0 

2 

see Table 5-29 

1 

2 

see 

Table 

5-30 

Operate delay 

+2 

2 

0-9999 (x 0.1 sec) 

Release delay 

+3 

2 

0-9999 (x 0.1 sec) 

Operate limit  

+4 
+5 

4 see 

Table 

5-29 

Release limit 

+6 
+7 

4 see 

Table 

5-29 

1.   The setpoint is disabled when the first trigger ID is set to NONE. To disable the setpoint, write zero into 

this register. 

2.   When writing the setpoint registers (except the event when the setpoint is to be disabled), it is 

recommended to write all the setpoint registers using a single request, or disable the setpoint before 
writing into separate registers. Each value being written is checked for compatibility with the other 
setpoint parameters; if the new value does not conform to these, the request will be rejected. 

3.   Operate and release limits for the trigger parameters and their conversion scales are indicated in Table 

5-29. Each limit value occupies two contiguous registers, the first of which (low word) contains the limit 
value, and the second (high word) is reserved for long parameters. This register is always read as zero. 
When written, its value is ignored.  

4.   Limits indicated in Table 5-29 by a N/A mark are read as zeros. When writing, they can be omitted or 

should be written as zeros. 

5.   When a setpoint action is directed to a relay allocated to output energy pulses, an attempt to re-allocate 

it for a setpoint will result in a negative response.   

  
Table 5-29  Setpoint Trigger Parameters 

Trigger parameter 

Trigger Size,

Unit

 

 

 Limit/scale 

  

Con- 

 

ID 

byte

 

Low 

High 

version

None 
None 

0 2 

 

N/A 

N/A 

NONE 

Internal events (E) 

kWh import pulse 

1024 2 

   

N/A  N/A  NONE 

kWh export pulse 

1025 2 

   

N/A  N/A  NONE 

kvarh import pulse 

1027 2 

   

N/A  N/A  NONE 

kvarh export pulse 

1028 2 

   

N/A  N/A  NONE 

kvarh total pulse 

1029 2 

   

N/A  N/A  NONE 

kVAh total pulse 

1030 2 

   

N/A  N/A  NONE 

Start new demand interval 

1031 2 

   

N/A  N/A  NONE 

Start new tariff interval 

1032 2 

   

N/A  N/A  NONE 

Start new volt/ampere demand interval 

1033 2 

   

N/A  N/A  NONE 

Start new sliding window demand interval 

1034 2 

   

N/A  N/A  NONE 

Timers (E) 

Timer #1 

1280 

2  

 

N/A 

N/A 

NONE 

Timer #2 

1281 

2 

 

N/A 

N/A 

NONE 

Status inputs 

Status input #1 ON 

1536 

2  

 

N/A 

N/A 

NONE 

Status input #2 ON 

1537 

2 

 

N/A 

N/A 

NONE 

Status input #1 OFF 

34304  2 

 

N/A 

N/A 

NONE 

Status input #2 OFF 

34305  2 

 

N/A 

N/A 

NONE 

Pulse inputs (E) 

Pulse input #1 

1792 

2  

 

N/A 

N/A 

NONE 

Pulse input #2 

1793 

2 

 

N/A 

N/A 

NONE 

Phase reversal 

Positive phase rotation reversal 

 

35073 2 

 

 

N/A 

N/A 

NONE 

Negative phase rotation reversal 

 

35074 2 

 

N/A 

N/A 

NONE 

Pulse counters 

High pulse counter #1 

2560 

2  

 

0 

10

6

-1 NONE 

High pulse counter #2 

2561 

2 

 

0 

10

6

-1 NONE 

High pulse counter #3 

2562 

2  

 

0 

10

6

-1 NONE 

Содержание PM171 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды