manualshive.com logo in svg

Satec PM171 series, Справочное руководство

Поделиться
Скачать
Satec PM171 series Скачать руководство пользователя страница 28

27

 

5.10  Analog Output Setup Registers 

Table 5-19  Analog Output Allocation Registers 

Channel 

Registers (see Table 5-20) 

Channel #1 

3148-3150 

Channel #2 

3151-3153 

 

Table 5-20  Analog Channel Allocation Registers 

Parameter 

Offset 

Size,  byte 

Direction 

Range 

Output parameter ID 

+0 

2 

R/W 

see Table 5-23 

Zero scale (0-4 mA) 

+1 

2 

R/W 

see Table 5-23 

Full scale (1/20 mA) 

+2 

2 

R/W 

see Table 5-23 

1.   Except for the signed power factor (see Note 3 to Table 5-23), the output scale is linear within the value 

range. The scale range will be inverted if the full scale specified is less than the zero scale. 

2.   For bi-directional analog output (

±

1 mA), the zero scale corresponds to the center of the scale range (0 

mA) and the direction of the current matches the sign of the output parameter. For signed (bi-
directional) values, such as powers and signed power factor, the scale is always symmetrical with 
regard to 0 mA, and the full scale corresponds to +1 mA output for positive readings and to -1 mA 
output for negative readings. For these, the zero scale (0 mA output) is permanently set in the 
instrument to zero for all parameters except the signed power factor for which it is set to 1.000. In the 
write request, the zero scale is ignored. No error will occur when you attempt to change it. Unsigned 
parameters are output within the current range 0 to +1 mA and can be scaled using both zero and full 
scales as in the case of single-ended analog output.  

5.11  Analog Expander Setup Registers 

Table 5-21  Analog Expander Channel Registers 

Channel 

Registers (see Table 5-22) 

Channel #1 

3196-3198 

Channel #2 

3199-3201 

Channel #3 

3202-3204 

Channel #4 

3205-3207 

Channel #5 

3208-3210 

Channel #6 

3211-3213 

Channel #7 

3214-3216 

Channel #8 

3217-3219 

Channel #9 

3220-3222 

Channel #10 

3223-3225 

Channel #11 

3226-3228 

Channel #12 

3229-3231 

Channel #13 

3232-3234 

Channel #14 

3235-3237 

 

Table 5-22  Analog Channel Allocation Registers 

Parameter 

Offset 

Size,  byte 

Direction 

Range 

Output parameter ID 

+0 

2 

R/W 

see Table 5-23 

Zero scale (0-4 mA) 

+1 

2 

R/W 

see Table 5-23 

Full scale (20 mA) 

+2 

2 

R/W 

see Table 5-23 

Except for the signed power factor (see Note 3 to Table 5-23), the output scale is linear within the value range. 
The scale range will be inverted if the full scale specified is less than the zero scale. 

NOTE 

Analog expander outputs settings will not be in effect until the analog expander output is globally enabled. To 
activate the analog expander output, set the analog expander option to the enabled state in the user selectable 
options setup (see Section 5.3).  

 

Содержание PM171 series












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды