Sargent and Greenleaf 6128 Скачать руководство пользователя страница 31

Страница: 31 / 32

630-600

MODEL 6128/6129 PROGRAMMING & OPERATIONS GUIDE

Appendix A.

Specifications

Below are the specifications for the Comptronic Models 6128 and 6129 electronic safe locks

and 61KP keypads .

Lock dimensions

• Width: 2 .4 inches (62 mm)

• Height: 1 .1 inches (30 mm)

• Length: 3 .32 inches (84 mm)

Keypad dimensions

• 4 inches diameter (101 mm)

• Height: 1 .44 inches (36 mm)

Weight

• 1 pound (450 g)

• Housing/base: 0 .7 pound (320 g)

• Module: 1 pound (450 g

Shipping weight

• 2 .75 pounds (1250 g)

Finish

• Case: Black paint

• Cover: Black paint

• Keypad: Satin chrome plated (standard)

Power

• Two (2) 9-volt alkaline batteries in keypad

(Duracell recommended)

Battery life

• Approximately 5000 openings

(based on use of Duracell alkaline batteries)

Note:

Use of time delay will decrease

battery life .

Low battery detection

• Beep/LED flash feedback from keypad

(5 double beeps/flashes)

Operating temperature

• 32

to 120

F (0

to 50

Keep batteries fresh when operating

at lower temperatures

Seller warrants that for two (2) years from the date of shipment from Seller’s point of manufacture,

the goods will be free from defects in material and workmanship, provided the goods are normally

and properly used according to the Seller’s written instructions .

THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED . S & G DOES NOT WARRANT THAT THE GOODS ARE MERCHANTABLE OR FIT FOR

ANY PARTICULAR PURPOSE EXCEPT AS EXPRESSLY PROVIDED HEREIN .

Seller’s entire liability and Buyer’s exclusive remedy in the event that the goods do not conform to the

foregoing warranty shall be Seller’s repair or replacement of the goods (including payment of freight

costs to and from point of manufacture) . This warranty does not apply to batteries or damage from

battery leakage .

SELLER SHALL HAVE NO LIABILITY FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT OR SPECIAL

DAMAGES . SELLER DOES NOT WARRANT ITS LOCK PRODUCTS TO BE IMPERVIOUS TO FORCIBLE

OR SURREPTITIOUS ENTRY, AND SELLER SHALL HAVE NO LIABILITY FOR DAMAGE TO OR LOSS OF

PROPERTY SOUGHT TO BE PROTECTED BY ANY SUCH LOCK .

S&G Confidential

The information contained in this document is proprietary to Sargent & Greenleaf . Publication or

duplication of this copyrighted document is strictly prohibited .

WARRANTY

Comptronic Model 6128/6129 Electronic Safe Lock

And Model 61KP Keypad

Limited Warranty

Sargent & Greenleaf, Inc.
A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.
PO Box 930
Nicholasville, KY 40356
Phone: (800)-826-7652 Fax: (800)-634-4843
Phone: (859)-885-9411 Fax: (859)-887-2057

Sargent & Greenleaf S.A.

9, Chemin du Croset

1024 Ecublens, Switzerland

Phone: +41-21 694 34 00

Fax: +41-21 694 34 09

Содержание 6128

































Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды

Sargent and Greenleaf 6128, Руководство по программированию и эксплуатации

Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды