Sargent and Greenleaf 6128 Скачать руководство пользователя страница 29

Страница: 29 / 32

630-600

MODEL 6128/6129 PROGRAMMING & OPERATIONS GUIDE

4.3.6 — Set Clock Calendar:

This is a management only operation code that is used to reset the clock calendar setting

inside the lock . This code operates under specific parameters that are detailed in the Lock

Management System instructions . When this code is used, the lock will derive the date

information from the management touch key, however the time must be input through the keypad

by the user . The time should be set in HHmm format based on a 24-hour clock, where HH =

hours and mm = minutes . It is important to note that the time to be set is the local standard time

at the lock location . This code will not open the lock .

Example

Step 1.

User places his touch key in reader .

Step 2.

User inputs his four digit PIN and presses the # key .

Step 3.

User inputs the eight digit operation code and presses the # key .

Step 4.

Lock illuminates Amber “Mode” indicator during processing of code

Step 5.

At the successful completion of the processing the lock will flash the

Green “Status 1” indicator and emits five audible beeps .

Step 6.

User inputs new time on keypad in HHmm format and presses the # key

Step 7.

Lock responds with Green “Status 1” indicator and

emits three audible beeps .

Step 8.

User inputs time on keypad (HHmm) and presses the # again to confirm

Step 9.

Lock responds with Green “Status 1” indicator and emits

three audible beeps .

4.3.7 — Reset Lockout:

This is a management only operation code . This operation is used to reset the lock once it

is set in a lockout mode due to excessive unauthorized attempts to operate the lock with invalid

operation codes or bank user PIN codes . This code will not open the lock .

Example

Step 1.

User places his management touch key in reader .

Step 2.

User inputs his four digit PIN and presses the # key .

Step 3.

User inputs the eight digit operation code and presses the # key .

Step 4.

Lock illuminates Amber “Mode” indicator during processing of code .

Step 5.

At the successful completion of the reset operation, the lock will

flash the Green “Status 1” indicator and emit three beeps .

Step 6.

User removes touch key .

Содержание 6128

































Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды

Sargent and Greenleaf 6128, Руководство по программированию и эксплуатации

Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды