Sargent and Greenleaf 6128 Скачать руководство пользователя страница 6

Страница: 6 / 32

630-600

MODEL 6128/6129 PROGRAMMING & OPERATIONS GUIDE

Positions 00, 02, and 10 have default PIN Codes set at the factory:

PIN Position Description

PIN Position

Default PIN Code

Programmer Code

123456

Officer Code

020202

User Code

101010

Programmer Code (PC)

can only set-up the operating parameters of the lock and download

the audit trail data .

The Programmer Code cannot open the safe.

Bank User Group consists of up to 16 PIN Code positions; 2 Officers and 4 Administrators

who manage the lock programs and up to 10 Users who open and close the lock .

If the lock still has the original S&G factory default settings, you can open the lock by entering

a PIN position and PIN Code, which makes up an 8-digit User code, followed by the # key .

The lock is set to default to Multiple User mode which allows opening of the lock by entering

any valid code other than the Programmer Code . (See 3 .3

Setting Access Mode

) .

(If lock does not open and beep patterns were heard after pressing the # key, reference

section 2 .3 .1 “Beep Patterns” to identify condition .)

We recommend that Users change their PIN Codes immediately after the PIN positions are

assigned (Section 3 .1) .

2.1 — Bank User Group, PIN Positions, and User Codes

2.1.1 — Bank User Group

Bank User Group is the factory default and is always active in each lock (unless disabled

under Service Mode operation) . The Bank User Group has an access hierarchy of Officers

(PIN positions 02 and 03), Administrators (PIN positions 04, 05, 06 and 07), and Users (PIN

positions 10 through 19) . See Tables A&B beginning on the next page for access privileges .

Bank User Group can be configured to operate in three different User access modes .

• Multiple User mode

— any valid code for the lock (other than the Programmer Code) can be

used to open it .

• Manager / Employee mode

— the Officers or Administrators enable/disable the access

privilege of individual User Codes . When in this mode the officer and Administrator Codes do not

open the lock .

• Dual Control mode—

two independent User Codes are needed to open the lock . Officer and

Administrator Codes can be used to open the lock in this mode .

OPERATING THE LOCK

Содержание 6128

































Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды

Sargent and Greenleaf 6128, Руководство по программированию и эксплуатации

Результаты поиска

Содержание 6128

Отзывы:

Похожие инструкции для 6128

Бренды по названию

Популярные бренды