manualshive.com logo in svg

SANDVIK CH420:01, Руководство по установке

Поделиться
Скачать
SANDVIK CH420:01 Скачать руководство пользователя страница 93

7. Electrical installation

91

  

CH420:01 

© Sandvik SRP AB – Doc. no. S 223.510 en Ver. 1

7.3 Motors and heating elements

Starting equipment for the drive motor, auxiliary motors and heating 
elements are normally not supplied by Sandvik. Fuses, relays, motor 
protectors and control units must be installed in the appropriate switchgear 
cabinets.

7.3.1

M1 – Crusher motor

The power supply to the motor must incorporate the necessary fuses, relay 
and motor protector, all installed in an appropriate switchgear cabinet. 

The main drive motor of the crusher can be started in several different ways, 
depending on the power supply available:

•

Direct on-line starter

•

Electronic soft starter

Starting and stopping can be made possible either by buttons or via software.

7.3.2

M2 – Lubrication pump

The power supply to the motor must incorporate the necessary fuse, relay 
and motor protector, all installed in an electrical cabinet. Starting and 
stopping can be made possible either by buttons or via software. 

NOTE!

The M1 relay must be interlocked with the power supply to the crusher’s 
drive motor, so it is only possible to run the crusher when the lubrication 
pump M2 is in operation.

Содержание CH420:01















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды