Sanden SN3500, Руководство по установке

Страница: 130 / 150

A
A
B
B
C
C
D
D
E
E
4 4
3 3
2 2
1 1
Title
Size Document Number Rev
Create: Sheet of
Category
Mod: Tuesday, April 28, 1998
C
NAV-1 RS-232 GPS (INT RELAY)
Vista, Ca.
B
21 29
SN3500 INSTALLATION DRAWING
Sunday, December 09, 2007
Title
Size Document Number Rev
Create: Sheet of
Category
Mod: Tuesday, April 28, 1998
C
NAV-1 RS-232 GPS (INT RELAY)
Vista, Ca.
B
21 29
SN3500 INSTALLATION DRAWING
Sunday, December 09, 2007
Title
Size Document Number Rev
Create: Sheet of
Category
Mod: Tuesday, April 28, 1998
C
NAV-1 RS-232 GPS (INT RELAY)
Vista, Ca.
B
21 29
SN3500 INSTALLATION DRAWING
Sunday, December 09, 2007
A INITIAL RELEASE
DATE
6/9/98
REV
A
COMMENTS
GPS/LORAN RECEIVER.
KLN89-B SHOWN FOR
REFERENCE.
F
H
D
E
TO VHF NAV
RECEIVER
OBS OUT 34
37
OBS RETURN
OBS COS
36
OBS SIN
35
GPS DISPLAYED
31
NOTE 1
6
OBS RESOLVER H (IN)
9
18
8
SN3500
23
22
8
+TO
OBS RESOLVER E (VREF) (IN)
37
OBS RESOLVER COS OUT
7
38
37
24
ILS1 ENERGIZE
38
23
+FROM
36
OBS RESOLVER SIN OUT
P2
GPS SELECTED
ACFT PWR
GPS1 RELAY
7
4
K1
16
P1
29 LRN MSG IN
APPR- ANNUN
18
14 LRN APPR IN
ARM- ANNUN
17
44 LRN APPR ARM IN
WPT- ANNUN
15 43 LRN WPT IN
APPR ARM IN 8
MSG- ANNUN
10
APPR ARM OUT
P3
RS232-TX
3
P891
P892
!
MASTER MODE
SLAVE MODE
IN SLAVE MODE THE
RELAY DRIVE IS PART
OF THE EXTERNAL
SWITCH/ANNUNCIATOR
UNIT
GPS ENABLED FROM
SWITCH/ANNUNCIATOR UNIT.
(SLAVE MODE ONLY)
G
N/C
NOTE 6
C
NOTES:
1. CONNECT OBS "H" FROM RECEIVER "H" or "C" WHICHEVER IS THE
ACTIVE OUTPUT. CHECK APPROPRIATE NAV RECEIVER SCHEMATICS.
CONNECT "SIN OUT" and "COS OUT" TO THE ACTIVE RETURN PINS,
USUALLY D/F. CONNECT "OBS VREF" TO EITHER STATOR RETURN PIN
(REF OR GROUND) USUALLY E or G. THE LOAD RESISTOR SIMULATES
A SYNCHRO.
2. THESE CONNECTIONS FOR KX165 OR KNX80/81 PREVENT THE RECEIVER
FROM FLAGGING THE NAV SIGNAL WHEN THE RESOLVER IS BEING USED BY
THE GPS. CONSULT THE APPROPRIATE KING DOCUMENTATION FOR
FURTHER INFORMATION.
3. SEE ARINC-429 INSTALLATION PAGE WHICH DOES NOT REQUIRE THE
RESOLVER SWITCHING RELAY (WHERE APPLICABLE).
4. THE PREFERRED INSTALLATION IS THE SN3500 P3-7 CONTROLLING AN
EXTERNAL SWITCHING RELAY. IF AN EXISTING SWITCH CONTROL BOX IS
INSTALLED AND IT IS DESIRED TO LEAVE IT OPERATIONAL, USE P3-4 TO
SENSE GPS MODE AND SELECT SLAVE FOR THE MODE SETTING ON THE
OBS/RELAY/CDI MAINTENANCE PAGE.
5. CHECK MANUFACTURERS DOCUMENTATION FOR ANY ADDITIONAL
INSTALLATION SPECIFIC RELAY POLES WHICH MAY ALSO BE
NEEDED.
6. FOR 3V COMPOSITE NAV SOURCES INSERT A 470K SERIES RESISTOR
LOCATED AT THE SN3500 CONNECTOR. NOT REQUIRED FOR .5V
SOURCE.
1 MASTER: SN3500 CONTROLS THE NAV/GPS SWITCHING (PREFERRED)
2 SLAVE: EXTERNAL NAV/GPS SWITCH CONTROLS THE SN3500
KNS80, KNS81
ONLY
STATOR F
STATOR D
GROUND
ROTOR H
ROTOR C
KX165
ONLY
K1
DO NOT REVISE MANUALLY
COMPUTER CONTROLLED DRAWING
7. ONLY USED WHEN SN3500 IS IN MASTER MODE. SELECT GPS1 FOR
SENSE ON OBS/RELAY/CDI MAINTENANCE PAGE.
GPS1 SENSE
VERT +FLAG
ILS ENERGIZE
VERT -FLAG
VERT +DOWN
CO
MPO
S
IT
E 1
FROM VHF NAV RECEIVER
VERT +UP
P892
17
FCS LOC ENGAGE
Nav + Right
Nav + Left
Nav + Flag
Nav - Flag
GS - Flag
GS + Flag
GS + Up
GS + Down
Composite 1 In
KX165 / KNS80 / KNS81 SWITCHING, SEE NOTE 2
P1
P2
4
2
17
RS232-1 GROUND
82005-10
31
RS232-1 RX
A1 A/R 780 MINOR DOC CHANGES
B P3 PIN 4 RENAMED
1
SIGNAL GND
FOR AUTOPILOT INTERCONNT SEE PAGE "FCS DEVIATION (INTERNAL RELAY)
THIS DIAGRAM SHOWS USE OF INTERNAL NAV CONVERTER AND
DEVIATION RELAY OF SN3500
GPS SWITCHING RELAY CONNECTIONS (SEE NOTE 4)
CONNECT P3-4 OR P3-7 BUT NOT BOTH.
RELAY SENSE NOTE 7
C A/R 806 MINOR DOC CHANGE P1-22 AND P1-7
REVERSED, P2-37 WAS P2-7
ADDED ANALOG DEVIATION CONNECTIONS.
LAT +FLAG
LAT -FLAG
LAT +RIGHT
LAT +LEFT
+FROM
+TO
P892
10
11
11
12
32
33
P891
1N4004 1N4004
470K 470K
220 O
hm
220 O
hm
33K 33K
33K 33K