Samsung SL-M4580FX Скачать руководство пользователя страница 175

Страница: 175 / 252

4. Troubleshooting

► Error Code

C3–1312

► Error message

Imaging Unit Failure: #C3-1312. Install imaging unit again.

► Symptom

Toner sensor is defective. The machine can’t detect the sensor signal in the imaging unit normally.

► Troubleshooting method

1) Install the genuine samsung imaging unit.

2) If the imaging unit is already installed, check the following.

•

Reinstall the toner cartridge and imaging unit.

•

Check if the CRUM connector is normal.

•

Turn the machine off then on.

► Error Code

C3–1330

C3–1411

C3–1414

► Error message

Imaging Unit Failure: #C3-1330. Install imaging unit again.

Imaging unit is not installed. Install the unit

Imaging Unit Failure: #C3-1414. Install imaging unit again.

► Symptom

The imaging unit is not installed properly.

► Troubleshooting method

1) Open the front cover.

2) If the imaging unit is not installed, install it. Try to test the machine again.

3) If the imaging unit is installed, remove it. Check if the modular jack is contaminated or broken.

4) Clean the modular jack or replace the imaging unit.

5) If it is OK, check the CN22 harness connection on the main board.

6) If the harness is defective, replace it.

7) Turn the machine off then on. Try to test the machine.

4-72

Содержание SL-M4580FX






















































































































































































































































Результаты поиска

Содержание SL-M4580FX

Отзывы:

Похожие инструкции для SL-M4580FX

Бренды по названию

Популярные бренды

Samsung SL-M4580FX, Руководство по обслуживанию

Результаты поиска

Содержание SL-M4580FX

Отзывы:

Похожие инструкции для SL-M4580FX

Бренды по названию

Популярные бренды