manualshive.com logo in svg

Samson TROVIS 5432, Монтаж и эксплуатация

Поделиться
Скачать
Samson TROVIS 5432 Скачать руководство пользователя страница 5

1. Notes for the user

The controller is ready for operation with its factory (default) settings for temperatures and

time schedules.  
On start-up, after switching on the power supply, you must enter the 

current time and date

.

Refer to chapter 3 for further information about how to proceed. 
Times-of-use and room set points that can be easily changed by the end user are described

in chapter 5. In addition to this, the end user can make short-term changes to the reference

value or set point (chapter 4).
However, configuring the controller as well as setting the control parameters as described in

chapter 6 require specialized knowledge of heating systems and should only be performed

by an expert. This also applies for the description of the controller functions listed in chap-

ter 7.

PC-supported configuration

The TROVIS-VIEW Configuration and Operator Interface software allows you to create all

the configuration data on a PC/laptop and download them onto the controller via its in-

frared interface using an infrared adapter.
Refer to the operating instructions EB 5432-2 EN about how to configure the controller using

TROVIS-VIEW software. 

Validity of these mounting and operating instructions:

 

Firmware version 1.00 and higher

(Current Firmware version appears in the display for 2 s when the power supply is switched

on)

EB 5432-1 EN 

5

Notes for the user

Содержание TROVIS 5432







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды