Sakai SW884 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 127

background image

2 OPERATION

– 52 –

– 53 –

Emergency traveling

If the machine doesn’t move when you operate the forward and reverse control lever while
the engine is running, there may be a problem with the control system.
In this case, you may bypass the controller to temporarily drive the machine by following the
procedure below.

1) Push on the Parking brake switch. Shut off the engine and make sure the Emergency

propel switch is in the neutral position.

2) Identify the connectors PRO & EME on the SCR cover on right side of the machine.

3) Remove the plugs from connector PRO then exchange connectors PRO and EME.

4) Make sure the connectors are properly connected, close the hood but do not start the

engine until you have checked the surrounding area for obstacles.

Also make sure that the Emergency propel switch and traveling direction of the machine

are the same. Now it will be safe to move the machine to a safe area.

Fuel pre-filter

Right side of machine

[EME] Connector

[PRO] Connector

SCR cover

|

Parking brake switch

Emergency propel switch

«
...
55
56
57
58
59
...
»

Содержание SW884
































































































































Отзывы:

Нет отзывов

Похожие инструкции для SW884

Бренд: GE Страницы: 24

Бренд: C.M.O Страницы: 10

Бренд: Raymarine Страницы: 90

Бренд: K-LASER Страницы: 70

Бренд: K-LASER Страницы: 72

Бренд: LANGER EMV-Technik Страницы: 25

Electric Clamshell CSE12-208VCD

Бренд: Lang Страницы: 16

Бренд: ubicquia Страницы: 36

Бренд: mychway Страницы: 56

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

M-041 INDOOR CROSS

Бренд: Salter Страницы: 15

Бренд: Daekyung Страницы: 15

Бренд: ICON Страницы: 24

Бренд: HEINE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды