Sakai SW884 Скачать руководство пользователя страница 52

Страница: 52 / 127

2 OPERATION

– 48 –

2.3.2 Starting the engine

WARNING

• Check that there are no people or obstacles around the machine and beep the

horn before starting the engine.

• Set the Forward-Neutral-Reverse (F-N-R) lever in the neutral position and press

down the Parking brake switch before starting the engine.
Unless these conditions are met, the engine will not start.

1) Set the Engine speed selector switch in the IDLE position.

（±

50 min

-1

）

Engine

speed

IDLE

ECO

FULL

900 min

-1

1850 min

-1

2200 min

-1

2) Turn the Starter switch to the position and check that

the warning lamps and parking brake indicator lamp on
the monitor display are on.

Engine speed selector switch

ECO

IDLE

FULL

START

OFF

STOP

Содержание SW884
































































































































Результаты поиска

Содержание SW884

Отзывы:

Похожие инструкции для SW884

Бренды по названию

Популярные бренды

Sakai SW884, Руководство оператора

Результаты поиска

Содержание SW884

Отзывы:

Похожие инструкции для SW884

Бренды по названию

Популярные бренды