![background image](http://html1.mh-extra.com/html/ryobi/ws720/ws720_operators-manual_1505974010.webp)
10 — English
WARNINg:
In the event of a power failure or when the tool is not in
use, turn the switch
Off and remove the switch key.
This action will prevent the tool from accidentally starting
when power returns.
WARNINg:
ALWAYS make sure your workpiece is not in contact
with the cutting wheel before operating the switch to
start the tool. Failure to heed this warning may cause the
workpiece to be kicked back toward the operator and
result in serious personal injury.
WARNINg:
To reduce the risk of accidental starting, ALWAYS make
sure the switch is in the
Off position before plugging
tool into the power source.
USINg ThE RIP gUIDE AND MITER gUIDE
See Figure 13, page 18.
The rip guide can be used from both the left and right side
of the cutting wheel.
Turn knob on rip guide counterclockwise to loosen.
Adjust the rip guide in the desired position using the rip
guide scale, located on front and rear of table, to set rip
guide to desired width of cut.
Rotate the knob, clockwise, to tighten securely.
To adjust angles:
Adjust rip guide to desired position and secure tightly.
Slide miter guide onto rip guide from the front.
Adjust to desired angle using angle scale and tighten
securely with knob.
MAKINg CUTS
Always draw the line to be cut on the tile using a marker or
grease pencil. If the tile is shiny and hard-to-mark, place
masking tape on the tile and mark the tape.
A common problem when cutting tile is straying from the
marked line. Once you’ve strayed from the mark, you can not
force the wheel back to the line by twisting the tile. Instead,
back up and recut the tile slicing off a small amount of tile
until the wheel is back on track.
To avoid this problem, use the rip guide when making cross
cuts, the miter guide for miter cuts and the adjustable right
side table for making bevel cuts, whenever possible.
OPERATION
TO MAKE A CROSS CUT
See Figure 14, page 18.
Cross cuts are straight 90° cuts. The material is fed into the
cut at a 90° angle to the wheel, and the wheel is vertical.
Using a marker or grease pencil, mark the area to be cut
on material.
Adjust rip guide to desired position and secure tightly.
Place the material on the table and firmly against the rip
guide.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the
ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the rip guide and feed
the material into the cutting wheel.
When the cut is made, turn the saw
Off. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE A 45° DIAgONAL CUT
See Figure 15, page 18.
45° Diagonal cuts are also referred to as “long point to long
point cuts”.
Using a marker or grease pencil, mark the area to be cut
on material.
Set the rip guide to desired width, and tighten the knob
to secure in place.
Slide miter guide onto rip guide from front.
Adjust miter guide to 45° using angle scale and tighten
securely with knob.
Make sure the material is clear of the cutting wheel before
turning on the saw.
Turn the on/off switch to the
ON position.
Let the cutting wheel build up to full speed and wait for
the wheel to get wet before moving the material into the
wheel.
Hold the material firmly against the miter guide and slide
miter guide along rip fence. Feed the material into the
cutting wheel.
When the cut is made, turn the saw
Off. Wait for the
cutting wheel to come to a complete stop before remov-
ing any part of the material.
TO MAKE A MITER CUT
See Figure 16, page 18.
Miter cuts are used for cutting outside and inside corners
on material, decorative chair rail, and base molding with the
material at any angle to the wheel other than 90°. Miter cuts
tend to “creep” during cutting. This can be controlled by
holding the workpiece securely against the miter guide.
Содержание WS720
Страница 43: ...20 NOTES NOTAS...