Russound CAM6.6X-S1 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 116

background image

61

c. Selected: Default

Default selects the same device type and device code previously

(Deflt)

setup in BASIC SETUP. Procedure advances to KEY FUNCTION
(step 4)

d. Selected: Macro:

(To build macros, see Macro Editor page 65)

i. MACRO

-

Macro loads a series of commands which are processed when

(Macro)

activated.

ii. MACRO ID

–

Enter the macro ID number. Menu advances to SAVE CHANGES

(MacID)

(step 5)

e. All Other Selections:

Procedure advances to DEVICE CODE (step 3)

3. DEVICE CODE

–

Source component code for IR control.

(DevCd)

4. KEY FUNCTION

–

Select a function (Play, Enter, etc.).

(KeyFn)

5. SAVE CHANGES?

–

Select “yes” to save the changes.

(Save?)

# OF SOURCES (#Srcs)

At this field it is necessary to enter the number of sources used in the CAM6.6 system (1 to 6). This
limits the sources displayed on the keypad in the normal running mode when the source button is
pressed, but also limits source selections in the configuration menus.

See Source Select

Command & # Of Sources - Flow Chart page 73

ZONE SETUP (ZonSu)

NOTE: This procedure should be performed using the keypad installed in the zone to be configured.

See Zone Setup - Flow Chart page 74

Zone Setup allows the installer to adjust properties of the UNO Keypad controlled CAM6.6 zone. This
series of menus allows the system’s zones to be configured for these properties:

ZON VOL TRIM (ZonVT)

SYSON ENABLE (SysOn)

PARTY ENABLE (PtyEn)

MASTER ENABL (MstEn)

MUTE ENABLE (MutEn)

1. ZON VOL TRIM -

This feature allows the installer to adjust the output volume to

(ZonVT)

each zone. -16 dB (lowest) to 0 dB (max)(-3dB default).

2. SYSON ENABLE -

This feature is either disabled or enabled. If disabled (default), an

(SysOn)

All On command activated from another zone will not turn on the

INSTALLER

INSTALLATION MENU

«
...
59
60
61
62
63
...
»

Содержание CAM6.6X-S1





















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6X-S1

Бренд: Dish Network Страницы: 18

Бренд: PAG Страницы: 2

Бренд: Kathrein Страницы: 44

Бренд: Sylvania Страницы: 8

Бренд: Yaesu Страницы: 77

Бренд: Sangean Страницы: 6

Gewa Andromeda REC4

Бренд: Abilia Страницы: 48

Бренд: Barlow Wadley Страницы: 11

Бренд: Jensen Страницы: 28

Бренд: Ham radio Страницы: 14

Бренд: FTE Страницы: 25

Бренд: Ross Страницы: 36

Бренд: Akai Страницы: 15

Бренд: Avermedia Страницы: 1

Бренд: Yaesu Страницы: 68

Бренд: Blaupunkt Страницы: 8

Бренд: Blaupunkt Страницы: 20

My First Transceiver MFT-40

Бренд: EA3GCY Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды