Russound CAM6.6X-S1 Скачать руководство пользователя страница 34

Страница: 34 / 116

INSTALLER

UNO-S1 KEYPAD-INSTALLATION

Keypad Location

The best infrared remote performance is achieved
with the keypad away from any direct sunlight,
plasma TV, and low voltage lighting controls. Also
consider convenience when choosing a location.

Choose a place that is easily seen from the posi-
tion where a person is most likely to be located.

Check whether or not you can route the wire to
the location you have chosen.

Keypad Installation

To install a single-gang keypad, you will need to
use a UL/CSA approved plastic single-gang elec-
trical box.

Route CAT-5 wire to the junction box from the
CAM6.6.

Use the supplied 110 punchdown tool to con-
nect each wire to its corresponding color
labeled on the punchdown terminal.

Ensure jumper settings on keypads are in the
run positions.

Mount the keypad in the electrical box and
attach the cover plate. Repeat the steps until all
keypads are installed.

Blues

Junction Box UNO-S1 Back Plate Cover Plate

Содержание CAM6.6X-S1





















































































































Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды

Russound CAM6.6X-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды