Russound CAM6.6X-S1 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 116

background image

55

1. BUILD TIME

Displays the firmware Build Time of the tuner.

(BTime)

2. BUILD DATE

Displays the firmware Build Date of the tuner.

(BDate)

3. VERSION

Displays the firmware version of the tuner.

(Ver)

SOURCE SETUP (SrcSu)

Source Setup allows the system’s sources to be configured.

The following items can be found in the SOURCE SETUP menu:

BASIC SETUP (BasSu)

KEY CONFIG (KeyCf)

SOURCE NAMES (SrcNm)

SRC VOL TRIM (SrcVT)

NUMERIC IR (NumIR)

SRC SEL CMD (SrcSC)

# OF SOURCES (#Srcs)

BASIC SETUP (BasSu)

NOTE: The BASIC SETUP procedure should be performed for each source before proceeding to other
source setting changes.

NOTE: If the CAM6.6 has an optional internal source installed, it is pre-configured as Source 1, with
source name <XM> and command type Peripheral.

This procedure uses built-in source “templates” to quickly and easily configure the source settings
needed for basic operation of the source component. Before performing BASIC SETUP, connect the
source components to the CAM6.6 as outlined in the Source Connections section. Also be sure that
all sources are powered on.

See Basic Setup - Flow Chart 69

1. SOURCE NUM

–

Select the source to be configured.

(Src #)

2. SOURCE NAME

–

Select the name for the source (e.g., DVD, Aux 2, Jazz, etc.).

(Name)

3. COMMAND TYPE

–

Select the type of command template (e.g., CD, TV, etc.). Selecting

(CmdTp)

the command type template will tell the CAM6.6 how to configure the
key’s command and text for the source component.

INSTALLER

INSTALLATION MENU

«
...
53
54
55
56
57
...
»

Содержание CAM6.6X-S1





















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6X-S1

Бренд: R&S Страницы: 232

Бренд: WDS Страницы: 32

Бренд: Cadillac Страницы: 102

Newcastle VR-654BD

Бренд: Sherwood Страницы: 62

Бренд: Jensen Страницы: 12

Бренд: Magnadyne Страницы: 16

Бренд: SilverStone Страницы: 2

Бренд: Dual Страницы: 33

Бренд: Grundig Страницы: 38

Бренд: Lotek Wireless Страницы: 36

Бренд: CAME Страницы: 8

Бренд: Kramer Страницы: 2

Бренд: Yaesu Страницы: 17

Бренд: Jensen Страницы: 32

Бренд: AFi Страницы: 4

Бренд: Streetwize Страницы: 5

Бренд: StarTech.com Страницы: 10

Бренд: Strong Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды