Russound CAM6.6X-S1 Скачать руководство пользователя страница 11

Страница: 11 / 116

USER

OPERATION

UNO-S1 Keypad

Zone On/Off

Press and release

to turn on the UNO

System Keypad. This also turns on the corre-

sponding CAM6.6’s room, and any presets previ-

ously assigned will be activated, including set-

tings for bass, volume, last source selected,

etc. Press and release

to turn off the UNO

System Keypad. This will also put the corresponding

CAM6.6’s room into a standby state.

System All On/Off

An “All On” command is issued by pressing

and holding for 3 seconds, after an initial room

has been turned on. An “All Off” command can

be issued to all rooms by pressing and holding

after the room has been turned off.

System On Indicator

When the room is off, but the system is on in

another room,

is illuminated by a green

backlight and the "SYS ON" icon remains visible.

Source Select Button

scrolls through the audio source inputs. To

change sources, press and release

. As the

sources are sequentially selected, each source's

name appears on the keypad LCD panel. When

a source is selected in more than one room, the

“SHARED” icon will appear on all UNO Keypads

using that source.

is also used to enter the

User Menu with a press and hold action. (See

next page for User Menu)

Volume Up/Down Buttons

The room’s audio output is adjusted using

Command Keys

The command keys

allow control of the

selected source at the UNO Keypad. The command

keys are activated with a press and release, or

press and hold to access secondary functions.

Содержание CAM6.6X-S1





















































































































Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды

Russound CAM6.6X-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды