Russound CAM6.6X-S1 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 116

background image

53

The following items make up the Installation Menu:

PERIPH SETUP (PerSu)

SOURCE SETUP (SrcSu)

ZONE SETUP (ZonSu)

CTRLR SETUP (CtlSu)

POWER MGT (PwMgt)

LEARN IR (LrnIR)

MACRO EDITOR (MacEd)

SYSTEM INFO (SInfo)

PERIPH SETUP (PerSu)

Peripheral Setup allows the CAM6.6’s optional internal source to be configured.

The following items can be found in the PERIPH SETUP menu:

MEM NAME (MemNm)

BANK NAME (BnkNm)

CONTROLLR ID (CtlId)

DIAGNOS-

TICS (Diags)

FACTORY INIT (FInit)

SYSTEM INFO (SInfo)

MEM NAME (MemNm)

NOTE: A memory preset must be created and saved before it can be named. Once it is saved, the
preset’s Tuner #, Bank # and Memory # must be entered in the following procedure.

This procedure accesses a name entry field to enter a custom name for a memory preset.

See

Periph Setup - Flow Chart page 67

1. BANK #

–

Select the BANK # of the memory preset.

(Bank#)

2. MEMORY #

–

Select the MEMORY # of the preset to be named.

(Mem #)

3. MEMORY NAME

–

Use the up/down keys to select a character and left/right keys

(MemNm)

to change a character position. A blinking cursor indicates the
placement of the character being entered. Names can be from 1
to 12 characters in length.

BANK NAME (BnkNm)

This procedure accesses a name entry field to enter a custom name for each of the tuner’s six
banks.

See Periph Setup - Flow Chart page 67

1. BANK #

–

Select the BANK # of the memory preset.

(Bank#)

INSTALLER

INSTALLATION MENU

«
...
51
52
53
54
55
...
»

Содержание CAM6.6X-S1





















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6X-S1

Бренд: Harman Kardon Страницы: 15

CQDP383U - AUTO RADIO/CD DECK

Бренд: Panasonic Страницы: 15

CQRX400U - AUTO RADIO/CD/MP3 DECK

Бренд: Panasonic Страницы: 44

Бренд: JBL Страницы: 105

Бренд: LAPIS Semiconductor Страницы: 12

Phase Linear CD1211

Бренд: Phase Linear Страницы: 20

Бренд: Axxera Страницы: 32

Бренд: PCB Piezotronics Страницы: 17

Бренд: Dedicated Micros Страницы: 148

Бренд: F&U Страницы: 14

Бренд: Icom Страницы: 8

Бренд: Hammarlund Страницы: 81

ATLONA HDR-EX-70-2PS

Бренд: Panduit Страницы: 12

Бренд: Delco Страницы: 18

Бренд: TANDBERG Страницы: 114

Бренд: HiTV Страницы: 28

Бренд: Crypto Страницы: 26

Бренд: Sigma Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды