Russound CAM6.6X-S1 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 116

background image

26

INSTALLER

GETTING STARTED

Unpacking the System Components

• Keep the original carton and packing materials
for future shipment or storage.

• Check for any visible signs of damage. If you
encounter any concealed damage, consult your
Russound dealer before proceeding to install the
unit.

• Retain the sales receipt as it establishes the
duration of the limited warranty and provides
information for insurance purposes.

CAM6.6X-S1/S2 System Components:

• 1 (one) CAM6.6 Controller/Amplifier

• 1 (one) UNO-S2 System Control Keypad

• 5 (five) UNO-S1 System Control Keypads

• 1 (one) UNO-LRC1 Learning/Preprogrammed

Remote Control

• 6 (six) 845.1 Micro Emitters

Tools needed for installation:

• Drill with a 1/2” x 6” drill bit

• Keyhole saw

• Flat head screwdriver (medium size)

• Phillips Screwdriver (cordless recommended)

• 110 punchdown tool (included)

• Modular RJ-45 crimper and connectors

• Pair of diagonal cutters or wire strippers

• Stud finder

• Steel wire fish tape

• Cable staples

• Double-gang electrical work box

• Single-gang electrical work boxes

System Installation Considerations

There are several factors to consider before
installing the Russound CAM6.6X-S1/S2 system:

• What are the intended listening zones?

• What system options and accessories might
be required for features such as local sources,
etc.?

• From where in each zone will the user prefer
to control the system? Where will the keypads
be located? Where will the speakers be located?

• Where will the source equipment be located?
The CAM6.6 must have proper ventilation above
and below for air circulation and heat dissipation.
A rack-mount location may require fans and vents.

Connection Tips

• It is recommended that the CAM6.6 and the
source equipment be plugged into a dedicated
20-amp circuit with an isolated ground. A power
line conditioner can reduce interference prob-
lems caused by noise found in some electrical
systems.

• Disconnect all live power cords before making
connections to the controller.

• Verify that all connections and polarity are
correct.

• Keep all power cords away from all signal
cables to prevent humming from induced noise.

• Choose reliable signal cables/patch cords.

• Label all wires with room location at both ends
of the wire.

«
...
24
25
26
27
28
...
»

Содержание CAM6.6X-S1





















































































































Отзывы:

Нет отзывов

Похожие инструкции для CAM6.6X-S1

Бренд: Ssl Страницы: 16

Бренд: Nauticam Страницы: 6

Бренд: Alinco Страницы: 48

Бренд: Pyle Страницы: 39

FTDX 9000 Series

Бренд: Yaesu Страницы: 12

Бренд: Aventura Страницы: 6

Бренд: Magnadyne Страницы: 16

Бренд: Zenith Страницы: 70

Бренд: Williams AV Страницы: 28

Бренд: Yaesu Страницы: 1

Бренд: Yaesu Страницы: 15

Бренд: Planet Audio Страницы: 16

Бренд: Dual Страницы: 88

Бренд: Small Wonder Labs Страницы: 26

Бренд: DX Engineering Страницы: 24

Бренд: Altronix Страницы: 8

Бренд: YouKits Страницы: 3

Бренд: Planet Audio Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды