Russound CAM6.6X-S1 Скачать руководство пользователя страница 21

Страница: 21 / 116

USER

INTERNAL SOURCE - XM TUNER

UNO-S2 Keypad Control

UNO-S2 Keypad Control of Tuner

Selecting the tuner

On the UNO-S2 keypad, press

to select the

XM Tuner by choosing the tuner’s preassigned

source number (1).

Selecting a Mode

Push

to toggle between XM modes.

Exiting a Mode

Press

to exit XM mode selection menu.

Selecting the desired channel

Use

and

for manual channel selection.

The channel will appear on the keypad. To move

quickly through the channels, press and hold

either

for more than 1.5 seconds

Signal Strength Mode

To check XM signal strength, press and hold

then release. The display shows the signal

strength rating. To exit, press

again.

Selecting a Bank

To select a bank, press and hold

for bank

up or

for bank down. The bank’s name will

be temporarily displayed on the UNO-S2.

Recalling a Memory Preset

Press

and

to scroll through the memo-

ry presets for the selected bank. This procedure

will step through all of the presets in the current

bank, then loop back to start at the first one.

Only configured presets will be displayed.

Mute

Press

to mute/unmute the tuner audio output.

Содержание CAM6.6X-S1





















































































































Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды

Russound CAM6.6X-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды