Russound CAM6.6X-S1 Скачать руководство пользователя страница 17

Страница: 17 / 116

Preset (default) Mode

This is the normal operating mode of the XM tuner for channel up and down, bank selection and
memory presets.

Next Preset

This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.

Previous Preset

This button press accesses the previous saved preset in the chosen bank

Next Bank

This button press accesses the next bank (total of 6 banks).

Previous Bank

This button press accesses the previous bank.

Channel Up

This button press accesses the next active channel up from the current channel.

Channel Down

This button press accesses the next active channel down from the current channel.

UNO-S1

UNO-S2

UNO-LRC1

Preset Mode

Next Preset

Previous Preset

Next Bank

Hold

Previous Bank

Hold

Channel Up

Hold

Channel Down

Hold

USER

INTERNAL SOURCE - XM TUNER

XM Radio Modes

Содержание CAM6.6X-S1





















































































































Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды

Russound CAM6.6X-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды