Russound CAM6.6X-S1 Скачать руководство пользователя страница 16

Страница: 16 / 116

XM Radio Modes

There are four user “modes” for selecting music on the XM Tuner:

Preset

(default or normal)

Category Search
Now Playing
Display Preferences

These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing

EXIT

and return to tuner display and Preset mode.

For all XM Modes

The chart below outlines the button presses for various XM tuner functions

outside of the XM modes.

If the UNO-S1 button operation is not specifically mentioned, use the UNO-LRC1 to
transmit commands through the UNO-S1.

Operating Mode Toggle

This button press accesses the three XM modes. The three modes will appear in order: Category
Search, Now Playing and Display Preferences.

Exit Current Mode

This button press returns the XM tuner to Preset (default) mode.

Signal Strength

This button press and hold accesses the Signal Strength mode. Depending on the signal, the follow-
ing will be displayed:

GOOD SIGNAL

Signal strength good

MARGINAL SIG

Signal strength marginal

POOR SIGNAL

Signal strength poor

NO SIGNAL

Loss of signal

Press the appropriate button again to exit Signal Strength Mode.

UNO-S1

UNO-S2

UNO-LRC1

All User Modes

Operating Mode Toggle

Exit Current Mode

Signal Strength

Hold

USER

INTERNAL SOURCE - XM TUNER

XM Radio Modes

Содержание CAM6.6X-S1





















































































































Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды

Russound CAM6.6X-S1, Инструкция по эксплуатации

Результаты поиска

Содержание CAM6.6X-S1

Отзывы:

Похожие инструкции для CAM6.6X-S1

Бренды по названию

Популярные бренды