Ruckus Wireless ICX 7850 Series Скачать руководство пользователя страница 35

Страница: 35 / 102

Ruckus ICX 7850 Switch Hardware Installation Guide

Part Number: 53-1005580-01

Mounting the Device

Installing the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295)

Time and Items Required

Allow 15 to 30 minutes to complete this procedure.

The following items are required to install the device using the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295):

•

Clamps or other means of temporarily supporting the device in the rack

•

#2 Phillips torque screwdriver

•

1/4-inch slotted-blade torque screwdriver

Parts List

The following parts are provided with the 1U, 1.5U, and 2U Universal Kit for Four-Post Racks (XBR-R000295) installation.

FIGURE 15

Rack Kit Parts

Flush-Front Mounting the Device in the Rack

NOTE

The illustrations in the rack installation procedures are for reference only and may not show the actual device.

Front brackets (2)

Screw, 8-32 x 5/16-in., panhead Phillips (8)

Bracket extensions (2)

Screw, 8-32 x 5/16-in., flathead Phillips (16)

Rear brackets, short (2)

Screw, 6-32 x 1/4-in., panhead Phillips (8)

Rear brackets, medium (2)

Screw, 10-32 x 5/8-in., panhead Phillips (8)

Rear brackets, long (2)

10 Retainer nut, 10-32 (8)

CAUTION
The device must be turned off and disconnected from the fabric during this procedure.

Содержание ICX 7850 Series







































































































Результаты поиска

Содержание ICX 7850 Series

Отзывы:

Похожие инструкции для ICX 7850 Series

Бренды по названию

Популярные бренды

Ruckus Wireless ICX 7850 Series, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7850 Series

Отзывы:

Похожие инструкции для ICX 7850 Series

Бренды по названию

Популярные бренды