Rohde & Schwarz NGMO1 Скачать руководство пользователя

Страница: 49 / 76

Repair

Power Supply NGMO

8.1.6

Display Unblank Test

Description This test is performed to determine whether all pixels of the LC display

can be switched on. After starting this test the LC-display should show

grey blocks with all pixels in place.

Function test

•

Switch on all pixels of the LC display using the following remote
command:

rus:service:select:function:test 2

•

Interrogate test 2:

rus:service:select:function:test?

The second command (interrogation command) is used to deter-

mine whether the test was successfully completed. The interroga-

tion command will keep on returning 65535, until the user either

presses the ENTER – key, or any other key on the unit.

ENTER:

•

The display shows the following message:

User Input:

Test: OK!

The interrogation command returns 0.

Any other key:

•

The display shows the following message:

User Input:

Test: FAILED!

The interrogation command returns 1.

Fault rectification

•

If an error occurs:

•

Replace the keyboard as described in chapter 9 or

•

replace the processor board as described in chapter 9.

3.00 / 05-2014

8-7

Содержание NGMO1













































































Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды

Rohde & Schwarz NGMO1, Руководство по обслуживанию

Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды