Rohde & Schwarz NGMO1 Скачать руководство пользователя страница 17

Страница: 17 / 76

Unit Description

Power Supply NGMO

4 Unit Description

Fig. 4-1 Power Supply NGMO2, Overall view

4.1 Introduction

The Power Supply NGMO is accommodated in a 1/2-19”, 2 HU (high

units) enclosure.

The NGMO is more, than just a power supply for conventional test and

measurement equipment, - it is an accurate, multipurpose electronic

device with two separate supply and measurement channels (NGMO2

only, NGMO1 only Channel A) which can be used as the following:

•

high speed voltage source,

•

programmable DC load,

•

precise digital multimeter,

•

sampling oscilloscope,

This unit fulfils all requirements of latest electronic battery-powered

communication products.

The high speed and the high reliability are features which are very im-

portant in a production environment.

The NGMO is an ideal device for testing complex high-tech products

such as mobile phones. With the NGMO, it is possible to create repro-

ducible and realistic powering conditions.

3.00 / 05-2014

4-1

Содержание NGMO1













































































Результаты поиска

Содержание NGMO1

Отзывы:

Бренды по названию

Популярные бренды

Rohde & Schwarz NGMO1, Руководство по обслуживанию

Результаты поиска

Содержание NGMO1

Отзывы:

Бренды по названию

Популярные бренды