Rohde & Schwarz NGMO1 Скачать руководство пользователя

Страница: 18 / 76

Power Supply NGMO

Unit Description

4.2 Function Description

The schedule at the service design concept is to replace the following

modules when a fault occurs.

•

Processor board

•

Keyboard / Display

•

Analog board ”A“ (NGMO1)

•

Analog boards ”A“ and ”B“ (NGMO2)

4.2.1

Prozessor Board

Apart from the control processor, its periphery and all data interfaces

the processor board also contains the rectification and filtering for the

electric power supply of the overall unit.

For this purpose the unit is equipped with two separate power supplies

with a transformer each. The mains supply voltage is channel separat-

ed and fed to the transformers via two fusible cut-outs on the processor

board. Separate fuses for 115VAC and 230 VAC are present.

The secondary voltages supplied by the transformers are rectified and

filtered on the processor board. Each of the two power supplies delivers

three non-stabilized direct voltages (approx. 8 VAC, 16 VAC, 21 VAC)

via the lateral connectors to the analog boards. A separate winding of

one of the two transformers generates the processor supply voltage

(+5 VDC) and stabilizes it on the board. On the processor board all di-

rect voltages are indicated by LEDs.

The alternating voltages arriving from the transformers are protected by

SMD-fuses directly after the connectors.

The processor establishes the data exchange between the remote con-

trol interfaces (RS232 and IEEE) and the signal processors on both

analog boards, interprets and saves measuring data as well as control

commands from the interfaces and from the keyboard. It additionally

presents data and modes on the display.

The periphery of the control processor consists of a main memory, an

EEPROM for storage of calibration data and adjustments as well as a

Flash-ROM to store the Firmware.

4-2

3.00 / 05-2014

Содержание NGMO1













































































Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды

Rohde & Schwarz NGMO1, Руководство по обслуживанию

Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды