Rohde & Schwarz NGMO1 Скачать руководство пользователя

Страница: 48 / 76

Power Supply NGMO

Repair

8.1.5

Display Blank Test

Description

This test is performed to determine whether all pixels of the LC display

can be switched off. After initiating the test the LC display should not

show any pixels.

Function test

•

Switch off all pixels of the LC display using the following remote
command:

rus:service:select:function:test 1

•

Interrogate test 1:

rus:service:select:function:test?

The second command (interrogation command) is used to deter-

mine whether the test was successfully completed. The interroga-

tion command will keep on returning 65535, until the user either

presses the ENTER – key, or any other key on the unit.

ENTER:

•

The display shows the following message:

User Input:

Test: OK!

The interrogation command returns 0.

Any other key:

•

The display shows the following message:

User Input:

Test: FAILED!

The interrogation command returns 1.

Fault rectification

•

If an error occurs:

•

Replace the keyboard as described in chapter 9 or

•

replace the processor board as described in chapter 9.

8-6

3.00 / 05-2014

Содержание NGMO1













































































Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды

Rohde & Schwarz NGMO1, Руководство по обслуживанию

Результаты поиска

Содержание NGMO1

Отзывы:

Похожие инструкции для NGMO1

Бренды по названию

Популярные бренды