background image

SRAM

®

 LLC WARRANTY

EXTENT OF LIMITED WARRANTY

Except as otherwise set forth herein, SRAM warrants its products to be free from defects in materials or workmanship for a period of two years after 
original purchase.

 

 This warranty only applies to the original owner and is not transferable. Claims under this warranty must be made through the 

retailer where the bicycle or the SRAM component was purchased. Original proof of purchase is required. 

Except as described herein, SRAM makes 

no other warranties, guaranties, or representations of any type (express or implied), and all warranties (including any implied warranties of 

reasonable care, merchantibility, or fitness for a particular purpose) are hereby disclaimed.

LOCAL LAW

This warranty statement gives the customer specific legal rights. The customer may also have other rights which vary from state to state (USA), from 
province to province (Canada), and from country to country elsewhere in the world.
To the extent that this warranty statement is inconsistent with the local law, this warranty shall be deemed modified to be consistent with such law, 
under such local law, certain disclaimers and limitations of this warranty statement may apply to the customer. For example, some states in the United 
States of America, as well as some governments outside of the United States (including provinces in Canada) may:

a. Preclude the disclaimers and limitations of this warranty statement from limiting the statutory rights of the consumer  

(e.g. United Kingdom).

b. Otherwise restrict the ability of a manufacturer to enforce such disclaimers or limitations.

For Australian customers:

This SRAM limited warranty is provided in Australia by SRAM LLC, 1000 W. Fulton Market, 4th Floor, Chicago, IL, 60607, USA. To make a warranty 
claim please contact the retailer from whom you purchased this SRAM product.  Alternatively, you may make a claim by contacting SRAM Australia, 6 
Marco Court, Rowville 3178, Australia. For valid claims SRAM will, at its option, either repair or replace your SRAM product.  Any expenses incurred in 
making the warranty claim are your responsibility.  The benefits given by this warranty are additional to other rights and remedies that you may have 
under laws relating to our products.  Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.  You are entitled 
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.  You are also entitled to 
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

LIMITATIONS OF LIABILITY

To the extent allowed by local law, except for the obligations specifically set forth in this warranty statement, in no event shall SRAM or its third party 
suppliers be liable for direct, indirect, special, incidental, or consequential damages. 

LIMITATIONS OF WARRANTY

This warranty does not apply to products that have been incorrectly installed and/or adjusted according to the respective SRAM user manual. The 
SRAM user manuals can be found online at sram.com, rockshox.com, avidbike.com, truvativ.com, or zipp.com.
This warranty does not apply to damage to the product caused by a crash, impact, abuse of the product, non-compliance with manufacturers 
specifications of usage or any other circumstances in which the product has been subjected to forces or loads beyond its design.
This warranty does not apply when the product has been modified, including, but not limited to any attempt to open or repair any electronic and 
electronic related components, including the motor, controller, battery packs, wiring harnesses, switches, and chargers.
This warranty does not apply when the serial number or production code has been deliberately altered, defaced or removed.
This warranty does not apply to normal wear and tear. Wear and tear parts are subject to damage as a result of normal use, failure to service 
according to SRAM recommendations and/or riding or installation in conditions or applications other than recommended.

Wear and tear parts are identified as:

• Dust seals
• Bushings
• Air sealing o-rings
• Glide rings
• Rubber moving parts
• Foam rings
• Rear shock mounting hardware 

and main seals

• Upper tubes (stanchions)

• Stripped threads/bolts 

(aluminium, titanium, magnesium 
or steel)

• Brake sleeves
• Brake pads
• Chains
• Sprockets
• Cassettes
• Shifter and brake cables (inner 

and outer)

• Handlebar grips
• Shifter grips
• Jockey wheels
• Disc brake rotors
• Wheel braking surfaces
• Bottomout pads
• Bearings
• Bearing races
• Pawls

• Transmission gears
• Spokes
• Free hubs
• Aero bar pads
• Corrosion
• Tools
• Motors
• Batteries

Notwithstanding anything else set forth herein

, the battery pack and charger warranty does not include damage from power surges, use of improper 

charger, improper maintenance, or such other misuse.
This warranty shall not cover damages caused by the use of parts of different manufacturers.
This warranty shall not cover damages caused by the use of parts that are not compatible, suitable and/or authorised by SRAM for use with SRAM 
components.
This warranty shall not cover damages resulting from commercial (rental) use.

Содержание reverb a2



















































Отзывы: