Rigol MSO5000 Series Скачать руководство пользователя страница 349

Страница: 349 / 358

Chapter 20 Remote Control

RIGOL

MSO5000 User's Guide

20-7

Remote Control via GPIB

Connect the device

Use the USB-GPIB interface converter to extend the GPIB interface for the

oscilloscope, and then use the GPIB cable to connect the oscilloscope to the PC

to realize remote control.

Install the driver of GPIB card

Correctly install the driver of the GPIB card which has been connected to the PC.

To Set the GPIB Address

Set the GPIB address of the oscilloscope according to the description in

"To Set

the GPIB Address"

Search for the device resource

Start Ultra Sigma, and then click

. A window is displayed as shown in

Figure (a). Click

and the software searches for the instrument

resource currently connected to the PC via the GPIB interface. The resource

found is displayed at the right of the window as shown in Figure (b). Click

to add it.

(a)

(b)

Note:

If you want to remove the resource, select the resource and then click

to remove it.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MSO5000 Series







































































































































































































































































































































































Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol MSO5000 Series, Руководство пользователя

Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды