manualshive.com logo in svg

Rigol MSO5000 Series, Руководство пользователя

Поделиться
Скачать
Rigol MSO5000 Series Скачать руководство пользователя страница 179

Chapter 6 Operations and Measurements

 

 

RIGOL

 

MSO5000 User's Guide

 

6-45 

Track Mode 

 

In this mode, you can adjust the two pairs of cursors (Cursor A and Cursor B) to 

measure the X and Y values on two different sources respectively. The points being 

measured on Cursor A and Cursor B are marked by 

  and 

  respectively. 

When the cursors are moved horizontally/vertically, the markers will position on the 

waveform automatically. When the waveform is expanded or compressed 

horizontally/vertically, the markers will track the points being marked at the last 

adjustment of the cursors.   

Note: 

When the delayed sweep function is enabled, the track cursor is within the 

expanded area. 

 

Press 

Mode

 to select "Track" to enable the cursor track function, and the 

measurement results will be displayed at the upper-left corner of the screen, as 

shown in the following figure. When you change the measurement parameter for the 

track mode, the measurement results will be changed accordingly. 

 

 

 

AX: indicates the X value at Cursor A.   

 

AY: indicates the Y value at Cursor A. 

 

BX: indicates the X value at Cursor B. 

 

BY: indicates the Y value at Cursor B. 

 

△

X: indicates the horizontal spacing between Cursor A and Cursor B. 

 

△

Y: indicates the vertical spacing between Cursor A and Cursor B. 

 

1/

△

X: indicates the reciprocal of the horizontal spacing between Cursor A and       

Cursor B. 

 

1.

 

Select Measurement Source 

 

Press 

AX Source

, then rotate the multifunction knob 

  to select the 

desired measurement source. Press down the knob to select it. You can also 

press 

AX Source

 continuously or enable the touch screen to select it. The 

available source channels are None, CH1-CH4, and Math1-Math4. 

 

Press 

BX Source

, then rotate the multifunction knob 

  to select the 

desired source (CH1-CH4). Press down the knob to select it. You can also 

press 

BX Source

 continuously or enable the touch screen to select it. Thea 

available source channels are None, CH1-CH4, and Math1-Math4. 

 

Note:

 Only channels currently enabled can be selected. 

 

2.

 

Select the Track Axis 

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MSO5000 Series







































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды