Rigol MSO5000 Series Скачать руководство пользователя страница 143

Страница: 143 / 358

Chapter 6 Operations and Measurements

RIGOL

MSO5000 User's Guide

6-9

Table 6-1 Window Function

Window

Function

Characteristics Waveforms Applicable to the

Window Function

Rectangular

Best frequency

resolution

Poorest

amplitude

resolution

Similar to the

situation when

no window is

applied.

Transient or short pulse, the signal

levels before and after the

multiplication are basically the same.

Sine waveforms with the same

amplitudes and rather similar

frequencies.

Wide band random noise with

relatively slow change of waveform

spectrum.

Blackman-Harris

Best amplitude

resolution

Poorest

frequency

resolution

Single frequency signal, searching for

higher order harmonics.

Hanning

Better frequency

resolution and

poorer amplitude

resolution

compared with

Rectangular

Sine, periodic, and narrow band

random noise.

Hamming

A little bit better

frequency

resolution than

Hanning

Transient or short pulse, the signal

levels before and after the

multiplication are rather different.

Flattop

Measure the

signals

accurately

Measure the signal that has no

accurate reference and requires an

accurate measurement

Triangle

Better frequency

resolution

Measure the narrow band signal and

that has strong noise interference



For FFT math operation setting label, refer to descriptions in

"Math Operation

Label"



Press

More



More



Color Grade

to enable or disable the color grade

display of the FFT operation results. When enabled, different colors are

displayed on the screen to indicate the times of data acquisition or acquisition

probability.



Press

More



More



Reset Color Grade

to clear the color grade display

and display the color grade again.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MSO5000 Series







































































































































































































































































































































































Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol MSO5000 Series, Руководство пользователя

Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды