Rigol MSO5000 Series Скачать руководство пользователя страница 33

Страница: 33 / 358

Chapter 1

Quick Start

RIGOL

MSO5000 User's Guide

1-11

Trigger Out and Pass/Fail



TRIG OUT:

The oscilloscope can output a signal that can reflect the current

capture rate of the oscilloscope at each trigger via this interface.

Connect the signal to a waveform display device and measure the

frequency of the signal. The measurement result is the same as the

current capture rate.



Pass/Fail

The instrument can output a pulse from the

[TRIG OUT]

connector

when a pass/failed event is detected during the pass/fail test.

AC Power Cord Connector

Indicates the input terminal where AC power source is connected. The

power supply requirements of the instrument are: 100 V~240 V; 45

Hz~440 Hz. Please use the power cord provided in the accessories to

connect the oscilloscope to the AC power source.

Kensington Lock Hole

You can lock the instrument to a fixed location by using the security lock

(please purchase it by yourself) via the lock hole.

Tip

After the oscilloscope is connected to network (if you do not have the access

to the Internet, please ask the administrator to open the specified network

authority), you can perform online upgrading for the system software:
1)

Enable the touch screen function. Tap the function navigation icon

at the lower-left corner of the touch screen to enable the function

navigation.

Tap the "Help" icon, and then the "Help" menu is displayed on the

screen.

Press

Online upgrade

or enable the touch screen to tap "Online

upgrade", then a "System Update Information" window is displayed,

requesting you whether to accept or cancel "RIGOL TERMS OF ONLINE

UPGRADE SERVICE". Tap "Accept" to start online upgrade. Tap "Cancel"

to cancel the online upgrade.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание MSO5000 Series







































































































































































































































































































































































Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol MSO5000 Series, Руководство пользователя

Результаты поиска

Содержание MSO5000 Series

Отзывы:

Бренды по названию

Популярные бренды